JVC KW-AVX900 manual Installing the remote controller, Parts list for installation and connection

Note: Be sure to keep all the screws and parts removed from your car for future use.

2 Attach the mounting brackets (removed from the car), to this unit (see below).

3 Connect the supplied cords.

• See page 2 for connecting the power cord.

• See page 3 for connecting the TV aerials, AV I/O cord and reverse gear signal extension cord.

• See page 4 for connecting the 5.1CH (LINE OUT) cord.

4 Install this unit using the screws removed in step 1.

The following example is for installation in a Toyota car. For more details, consult your JVC car audio dealer.

Remove the audio system originally installed in the car, together with its mounting brackets.

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Before installing the unit

• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could become loose or damaged.

• When tightening screws or bolts, be careful not to pinch any connection cord.

• Make sure not to block the fan on the rear panel to maintain proper ventilation when installed.

Heat sink

1

Unit: mm

KW-AVX900

Installation/Connection Manual

LVT1670-005A

[A]

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

WARNINGS

•DO NOT install any unit and wire any cable in locations where;

–it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.

–it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident.

–it may obstruct visibility.

•DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident.

•The driver must not watch the monitor while driving. If the driver watches the monitor while driving, it may lead to carelessness and cause an accident.

•The driver must not put on the headphones while driving. It is dangerous to shut off the outside sounds while driving.

•If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident.

•If the parking brake is not engaged, “Parking Brake” flashes on the monitor, and no playback picture will be shown.

–This warning appears only when the parking brake wire is connected to the parking brake system built in the car.

Notes on electrical connections:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front,

with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “Amplifier

Gain” setting to prevent the speakers from being damaged (see page 60 of the INSTRUCTIONS).

•To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

•The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

0307MNMMDWJEIN

EN ©2007 Victor Company of Japan, Limited

Installing the remote controller

Holder

Double-sided adhesive tape

Remote controller

Required space for the monitor ejection		Install the unit at an angle of less than 30˚,
		taking it into account that the monitor
		would eject when in use.
	100
		30˚
160	90.4

Parts list for installation and connection

The following parts are provided for this unit.

If anything is missing, contact your dealer immediately.

Main unit Power cord AV I/O cord

Reverse gear signal extension cord	Flat head screws	Round head screws
	(M5 x 8 mm)	(M5 x 8 mm)

Remote controller / Holder Plate for use with a Nissan car 5.1CH (LINE OUT) cord

Batteries Crimp connectors

Aerial cords

TV aerials Clamps

Rubber spatula Earth tape Cleaner

When installing the unit in a Nissan car

Plate for use with a Nissan car

Supplied screws

Mounting bracket removed from the car

Mounting bracket removed from the car

Screws removed from the car in step 1

Supplied screws

If necessary, restore the protruding tabs.

Select the appropriate type fitting to your audio system space.

Note : When installing the unit on the mounting bracket, make sure to use the supplied screws (M5 x 8 mm). If longer screws are used, they could damage the unit.

1