Tascam DA-40 Shift functions, INS/+ and DEL, ID markers START, SKIP, END, Char and renumbering

Page 22

4 - SHIFT functions

These functions of the tape deck are typically accessed by pressing SHIFT [31] so that the indica- tor is lit.

While the indicator is lit, the command keys take on their shifted function, labeled in blue above the key.

4.1 REPEAT

Repeated presses of the REPEAT key [20] cycle through the following:

•A-B repeat— the display shows REPEAT A-B— playback is repeated between the two location memory points (A refers to location memory point 1, and B refers to location memory point 2). The points must first be set (see 4.6, "Location memo- ries"), the tape located to a position between the two location memory points, and playback started from there.

•Single repeat— the display simply shows REPEAT— a program will be repeated; use the DATA dial or the INS/+ and DEL/- keys to select a program number, and then press PLAY to start repeated play of that program . While the program is being played back, the word REPEAT will flash in the display. If the REPEAT setting is being made while the tape is playing back, the program which starts with the next START ID encountered during playback will be repeated.

•All repeat— the display shows ALL REPEAT— the complete contents of the tape will be repeated If the REPEAT setting is being made while the tape is playing back, ALL REPEAT will start as soon as an END ID or the end of the tape is encountered.

•No repeat— the display does not show any repeat information

The number of times that the selected portion (A-B, program or tape) is repeated is set by the repeat menu option described in 3.8, "Repeat mode".

4.2 CHECK

This key [21] is used when entering characters for tape or program titles. It allows the checking of titles which are longer than the display allows, and scrolls them across the display. See “Character editing (titling)” on page 26

4.3 INS/+ and DEL/-

These keys may be used in addition to the data dial to increment and decrement values in the menus (see 3, "Menu functions").

NOTE

Remember that menus are unshifted func- tions. To use these keys as increment and decrement keys in the menus, the SHIFT indi- cator must be lit, which means that the SHIFT key must be pressed after the menu has been entered.

They are also used or incrementing and decrement- ing numeric values in the edit screens (see 4, "SHIFT functions").

When these keys are used for editing values, pressing and holding down these keys will repeat the incre- ment or decrement operation.

When entering characters (see 4.8, "Character editing (titling)"), the INS/+ key inserts a blank space into the character string immediately before the cursor position. The DEL/- key deletes the character at the cursor position.

4.4ID markers (START, SKIP, END, CHAR and renumbering)

These ID markers are used to control tape operations when they are read on playback. Briefly:

•START IDs are nine seconds in length. They are used to mark the beginning of a program and are usually in continuous sequence (from 01 to 99). If they somehow get out of sequence, the renumber facility is used to correct this.

•SKIP IDs are one second in length, and are used in skip play mode (see SKIP PLAY [24]) to skip past unwanted sections of tape

•END IDs are nine seconds in length, and are used to mark the “logical” end of a tape (even though there may be tape remaining, playback will stop when an END ID is encountered). There should, naturally, only be one END ID on a tape.

The above three ID types are recognized by every kind of DAT deck and player.

This tape deck also provides another kind of subcode ID marker:

22 TASCAM DA-40

Page 21 Page 23
Image 22
Page 21 Page 23
Contents DA-40 Important Safety Precautions Important for U.K. CustomersImportant Safety Instructions Table of Contents Specifications Introduction to the DA-40 FeaturesInstallation of the tape deck Unpacking and inspectionMaking connections Block Diagram Power connectionsFront and Rear panels Recording mode and source switches, etc Power and displayParts of the tape deck Tape controls Play key REW and F FWD keysStop key Pause keyShuttle wheel REC Mute keyData dial Margin Reset Command keysCounter Mode CharSkip Play Single PlayRear panel Balanced Analog Outputs Auto ID level Menu functionsDrum time head time Auto ID timeDigital output format Repeat modeRecord mute time Copy prohibit14Initializing settings 10End tally signal12Fast forward mode 15Viewing points at which block errors have occurredMenu functions INS/+ and DEL Shift functionsID markers START, SKIP, END, Char and renumbering Manually writing a Start or Skip ID Selecting an ID modeWriting a Start or Skip ID Erasing an END ID Writing an END IDErasing a Start or Skip ID Erasing titlesLocation memories Setting location memoriesEdit key Locating to location memoriesCharacter editing titling Program modeEntering and editing titles Deleting a title Writing the title to tapeChecking a title Copying and pasting a titleOPEN/CLOSE RC-D45 remote control unit optionID Select PositionRepeat Remote control transport keysREC Mute Specifications SpecificationsAudio specifications Physical specificationsDimensional drawing Error messages Serious error messagesIndex a O Auto IDIndex P SpdifDA-40
Related manuals
Manual 34 pages 32.84 Kb

DA-40 specifications

The Tascam DA-40 is a professional-grade digital audio tape recorder designed for a variety of audio production applications, including music recording, broadcasting, and post-production. Known for its durability and reliability, the DA-40 has established itself as a popular choice among sound engineers and musicians.

One of the main features of the Tascam DA-40 is its ability to record in both high-quality digital formats and traditional DAT (Digital Audio Tape). It supports sampling rates of 44.1 kHz and 48 kHz, which are industry standards for audio recording. This flexibility allows users to choose the format that best suits their workflow, making it an excellent tool for archiving, mastering, or live recording.

The DA-40 employs advanced digital processing technologies to provide superior sound quality. Its 20-bit digital audio converter ensures that recordings are captured with precision and clarity, preserving the nuances of the source material. Additionally, the DA-40 features a dynamic range of 100 dB, contributing to its reputation for delivering high-fidelity audio.

For ease of operation, the DA-40 is equipped with an intuitive user interface. The front panel includes an alphanumeric display that provides essential information like track status, timecode, and remaining tape length, making it user-friendly even in complex recording situations. The machine also offers multiple transport controls, allowing for precise navigation through recordings during playback or editing.

Another characteristic of the DA-40 is its versatility in connectivity options. It features balanced XLR inputs and outputs, along with unbalanced RCA connections, making it compatible with a wide range of audio equipment. The built-in S/PDIF digital output allows for seamless integration with digital audio workstations and other digital devices, enhancing its usability in modern studio environments.

The Tascam DA-40 is also designed with reliable performance in mind. Its rugged construction ensures that it can withstand the demands of live environments while providing consistent operation. Moreover, the unit supports automatic tape advance and rewind functions, streamlining the workflow for busy professionals.

In conclusion, the Tascam DA-40 is a highly capable digital audio tape recorder that combines advanced recording technology with user-friendly features. Its flexibility in audio formats, high-quality sound reproduction, versatile connectivity options, and durable design make it an essential tool for audio professionals aiming to achieve the best results in their production endeavors.
Top Page Image Contents