Tascam DA-40 Writing an END ID, Erasing a Start or Skip ID, Erasing an END ID, Erasing titles

Page 24

4 - SHIFT functions

Use the INS/+ and DEL/- keys or the DATA dial to adjust the offset backwards or forwards by up to 50 frames in either direction.

Press PLAY to preview the location of the ID point. The tape will rewind to the position, with the offset added or subtracted, and start playing back from the previewed ID position. While playing back, the word Posit will be shown on the display. When play- back stops after a few seconds, the offset value will replace the word Posit, and may be re-adjusted as described above.

Repeat the adjustment of the ID point and the pre- view of the point as many times as necessary.

When the ID point has been located satisfactorily, press ENTER. The display will show WR-STor WR-SK, depending on whether a START or SKIP ID is being written.

The edited point can also be used here as a location memory (use the MEMO 1 or MEMO 2 key).

The writing of the ID can be canceled at any time after POSITION has been pressed by pressing STOP.

4.4.4 Writing an END ID

Writing an END ID will stop the tape. If an END ID is written in the middle of recorded material, the material following the END ID will be inaccessible until the END ID is erased.

An END ID can be written from the record, or the record pause mode.

Select the END WRT option as described in 4.4.1, "Selecting an ID mode".

Press ENTER. The END ID will be written at the point that ENTER is pressed.

4.4.5 Erasing a START or SKIP ID

Select the START ERASE or SKIP ERASE option as described in 4.4.1, "Selecting an ID mode".

Locate the tape to a little after the START or SKIP ID to be erased or within the ID section itself.

Press ENTER. The tape will move backwards to find the first appropriate ID, and ER-STor ER-SKas appropriate is shown in the display. When the erase function is started, the tape will take some time to search for the ID and position itself appropriately.

When the ID has been located, the START ERASE or SKIP ERASE shown in the display will start flashing, and the RECORD and PLAY indicators will light.

After the ID has been erased, the deck will continue playing the tape.

NOTE

If a START ID is erased, the program num- bers will not be continuous. The renumbering function may be used to restore the sequence.

4.4.6 Erasing an END ID

Select END ERASE as the ID mode (see 4.4.1, "Selecting an ID mode").

Move the tape to a little after the END ID, and press

ENTER.

The tape will move back to the END ID and will erase it (the RECORD and PLAY indicators will both light). While the ID is being erased, the words END ERASE will flash in the display.

4.4.7 Erasing titles

If characters have been recorded on tape, the boxed word CHAR will appear on the bottom of the display (below the seconds digits).

To erase the characters which have been previously recorded as program titles, select CHAR ERASE as the ID mode (see 4.4.1, "Selecting an ID mode").

Move the tape to a little after the end of the START ID containing the characters to be erased,

Press ENTER; the display will show ER-CH, and the tape will start moving back until the START ID containing the characters is located on tape. The character information will then be erased (the RECORD and PLAY indicators will both light), but the START ID containing the title characters and the audio information will be retained. While the erase operation is taking place, the words CHAR ERASE will flash in the display.

4.4.8 Renumbering START IDs

If START IDs have been written to a tape after audio recording has taken place, or if START IDs have been removed from a sequence, the program num- bers will not form a continuous series.

To renumber the programs, select RENUM as the ID mode.

The right side of the display will show #01 (flash- ing), showing that the first START ID will be renum- bered as 01.

24 TASCAM DA-40

Page 23 Page 25
Image 24
Page 23 Page 25
Contents DA-40 Important Safety Precautions Important for U.K. CustomersImportant Safety Instructions Table of Contents Specifications Features Installation of the tape deckIntroduction to the DA-40 Unpacking and inspectionMaking connections Block Diagram Power connectionsFront and Rear panels Power and display Recording mode and source switches, etcParts of the tape deck Tape controls REW and F FWD keys Stop keyPlay key Pause keyREC Mute key Shuttle wheelData dial Command keys Counter ModeMargin Reset CharSkip Play Single PlayRear panel Balanced Analog Outputs Menu functions Drum time head timeAuto ID level Auto ID timeRepeat mode Record mute timeDigital output format Copy prohibit10End tally signal 12Fast forward mode14Initializing settings 15Viewing points at which block errors have occurredMenu functions Shift functions INS/+ and DELID markers START, SKIP, END, Char and renumbering Selecting an ID mode Manually writing a Start or Skip IDWriting a Start or Skip ID Writing an END ID Erasing a Start or Skip IDErasing an END ID Erasing titlesSetting location memories Edit keyLocation memories Locating to location memoriesProgram mode Character editing titlingEntering and editing titles Writing the title to tape Checking a titleDeleting a title Copying and pasting a titleRC-D45 remote control unit option ID SelectOPEN/CLOSE PositionRemote control transport keys RepeatREC Mute Specifications Audio specificationsSpecifications Physical specificationsDimensional drawing Error messages Serious error messagesIndex a O Auto IDIndex P SpdifDA-40
Related manuals
Manual 34 pages 32.84 Kb

DA-40 specifications

The Tascam DA-40 is a professional-grade digital audio tape recorder designed for a variety of audio production applications, including music recording, broadcasting, and post-production. Known for its durability and reliability, the DA-40 has established itself as a popular choice among sound engineers and musicians.

One of the main features of the Tascam DA-40 is its ability to record in both high-quality digital formats and traditional DAT (Digital Audio Tape). It supports sampling rates of 44.1 kHz and 48 kHz, which are industry standards for audio recording. This flexibility allows users to choose the format that best suits their workflow, making it an excellent tool for archiving, mastering, or live recording.

The DA-40 employs advanced digital processing technologies to provide superior sound quality. Its 20-bit digital audio converter ensures that recordings are captured with precision and clarity, preserving the nuances of the source material. Additionally, the DA-40 features a dynamic range of 100 dB, contributing to its reputation for delivering high-fidelity audio.

For ease of operation, the DA-40 is equipped with an intuitive user interface. The front panel includes an alphanumeric display that provides essential information like track status, timecode, and remaining tape length, making it user-friendly even in complex recording situations. The machine also offers multiple transport controls, allowing for precise navigation through recordings during playback or editing.

Another characteristic of the DA-40 is its versatility in connectivity options. It features balanced XLR inputs and outputs, along with unbalanced RCA connections, making it compatible with a wide range of audio equipment. The built-in S/PDIF digital output allows for seamless integration with digital audio workstations and other digital devices, enhancing its usability in modern studio environments.

The Tascam DA-40 is also designed with reliable performance in mind. Its rugged construction ensures that it can withstand the demands of live environments while providing consistent operation. Moreover, the unit supports automatic tape advance and rewind functions, streamlining the workflow for busy professionals.

In conclusion, the Tascam DA-40 is a highly capable digital audio tape recorder that combines advanced recording technology with user-friendly features. Its flexibility in audio formats, high-quality sound reproduction, versatile connectivity options, and durable design make it an essential tool for audio professionals aiming to achieve the best results in their production endeavors.
Top Page Image Contents