JVC GET0287-003A manual More about this receiver

Page 21

More about this receiver

Basic operations

Turning off the power

If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power.

Tuner operations

Storing stations in memory

During SSM search...

All previously stored stations are erased and stations are stored newly.

Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency).

When SSM is over, the station stored in No. 1 will be automatically tuned in.

When storing a station manually, a previously preset station is erased when a new station is stored in the same preset number.

FM RDS operations

Network-Tracking Reception requires two types of RDS signals—PI (Programme Identification) and AF (Alternative Frequency) to work correctly. Without receiving these data correctly, Network- Tracking Reception will not operate.

If a Traffic Announcement is received, the volume level (TA Volume) automatically changes to the preset level.

Disc operations

General

This receiver has been designed to reproduce CDs, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA) format.

When a disc has been loaded, selecting “CD” for the playback source starts disc play.

Inserting a disc

When a disc is inserted upside down, the disc automatically ejects.

Do not insert 8 cm discs (single CD) and unusual shape discs (heart, flower, etc.) into the loading slot.

Playing a CD-R or CD-RW

Use only “finalized” CD-Rs or CD-RWs.

This receiver can play back multi-session discs; however, unclosed sessions will be skipped while playing.

Some CD-Rs or CD-RWs may not play back on this receiver because of their disc characteristics, and for the following causes:

Discs are dirty or scratched.

Moisture condensation occurs on the lens inside the receiver.

The pickup lens inside the receiver is dirty.

CD-R or CD-RW on which the files are written with “Packet Write” method.

There are improper recording conditions (missing data, etc.) or media conditions (stain, scratch, warp, etc.).

CD-RWs may require a longer readout time since the reflectance of CD-RWs is lower than that of regular CDs.

Do not use the following CD-Rs or CD-RWs:

Discs with stickers, labels, or protective seal stuck to the surface.

Discs on which labels can be directly printed by an ink jet printer.

Using these discs under high temperatures or high humidities may cause malfunctions or damages to discs.

Changing the source

If you change the source, playback also stops (without ejecting the disc).

Next time you select “CD” for the playback source, disc play starts from where it has been stopped previously.

Ejecting a disc

If the ejected disc is not removed within

15 seconds, the disc is automatically inserted again into the loading slot to prevent it from dust. (Disc will not play this time.)

General settings—PSM

If you change the “AMP GAIN” setting from “HIGH PWR” to “LOW PWR” while the volume level is set higher than “VOL 30,” the receiver automatically changes the volume level to “VOL 30.”

ENGLISH

21

Image 21
Contents KD-S1501/KD-G152/KD-G151 How to reset your unit How to forcibly eject a discContents How to use the Mode button How to read this manualParts identification Display windowControl panel KD-S1501/KD-G152/KD-G151 Getting started To turn off the powerCanceling the display Demonstrations Setting the clockTo activate the display demonstration When an FM stereo broadcast is hard to receive Radio operationsTo tune in to a station manually Listening to a preset station Manual presettingSSM Strong-station Sequential Memory PTY codes FM RDS operationsTA Standby Reception What you can do with RDSStoring your favorite programmes PTY Standby Reception Tracking the same programme Network-Tracking ReceptionTo fast-forward or reverse the track Disc operationsTo stop play and eject the disc To go to a particular track directlyMode Plays at random Mode Plays repeatedlySelecting the playback modes Prohibiting disc ejectionFor Preset values Sound adjustmentsTo do Range Adjusting the soundBasic procedure General settings PSMAF-REG Indications Selectable settings, referenceDetaching the control panel Detaching the control panelMaintenance More about this receiver Symptoms Causes Remedies TroubleshootingAudio Amplifier Section SpecificationsRemoving the receiver / Retrait de l’appareil Precautions on power supply and speaker connectionsTypical connections / Raccordements typiques Electrical ConnectionsHaving Trouble with operation? Refer to page of How to reset your unit