Kenwood KDC-DAB4551U Installation/connection, Basic procedure, Part list, KDC-DAB41U only

Page 30

Installation/connection

Part list:

 

A Faceplate

(×1)

B Escutcheon

(×1)

C Mounting sleeve

(×1)

D Wiring harness

(×1)

E Removal tool

(×2)

F DAB antenna film *1

(×1)

G DAB antenna amplifier *1

(×1)

H Cord clamper *1

(×3)

I Cleaner *1

(×1)

• *1 KDC-DAB41U only

Basic procedure

1Remove the key from the ignition switch, then disconnect the · terminal of the car battery.

2Install the DAB antenna.

\ <Installation the DAB antenna

(KDC-DAB41U only)> (page 34)

3Make proper input and output wire connections.

\<Wiring connection> (page 32)

4Install the unit to your car.

\<Installing the unit> (page 33)

5Reconnect the · terminal of the car battery.

6Reset the unit. (page 3)

Warning

■The unit can only be installed in a car with a 12 V DC power supply, negative ground.

■If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

■Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

■Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

■Be sure to ground this unit to the car’s chassis again after installation.

■If the power is not turned ON (“PROTECT” is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.

Caution

■If your car’s ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

■Install this unit in the console of your vehicle. Make sure the faceplate will not hit the lid of the console (if any) when closing and opening.

■After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

■Mount the unit so that the mounting angle is 30° or less.

■If the fuse blows, first make sure the wires are not touching to cause a short circuit, then replace the old fuse with one that has the same rating.

■Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the · wires or ground them to any metal part in the car.

30 English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents KDC-DAB41U KDC-DAB4551U Contents Safety PreparationBasic Operations When a call comes in, Call appearsWhen a call ends, Call disappear Muting upon the reception of a phone callWhen an iPod is connected or a disc is loaded General operationAdjusting the clock Canceling the display demonstrationSetting the demonstration mode Initial settings before operationsSelectable setting Preset Updating Service List information Selecting a serviceAlphabet Search for service Service list information must be obtained firstAdjust Settings mode settings Display SelectionProhibition Listening to the Radio Available Program TypeAvailable Announcement News SET Mono SETSet the displayed language with Language SEL AF SETStart playing a disc Start playing the disc changer optional accessoryListening to a Disc/ USB device/ iPod Start playing a USB device or iPodAll Random Play Selecting Repeat PlaySelecting Random Play Selecting Magazine Random PlayIPod control by Hand mode Alphabet Search for iPodMy Playlist for iPod Mode No * CancelsMplist Delete is selectable only when the source is iPod MplistAbout Audio file Handling discsDiscs that cannot be used About USB deviceFor details, see above URL About Kenwood Music EditorOperation of Hands-Free Phoning Pairing Registering from Bluetooth devicesWhen a cell-phone is connected, the BT indicator lights up ConnectionCalling a Number in the Phone Book Speed Dialing Preset DialMaking a Call Calling a Number in the Call LogCall Waiting Receiving a CallDuring a Call Clearing the Disconnection MessageDownloading the Phone Book To download automaticallyTo download from the cell-phone manually Registering from Bluetooth devices Bluetooth SetupRegistering Bluetooth Device Pairing Registering Special Bluetooth deviceRegistering Phone Book Name Selecting the Bluetooth DeviceSetting a Voice Command Registering Phone Book Name TypeVoice TAG Bluetooth SetupPairing Call BeepEC Level MIC GainNR Level About the Cell-PhoneDownloading the SMS SMS Short Message ServiceWhen a new message arrives Display the SMSListening to the other external components Unread messages are prefixed with an asteriskFunction settings Display ClockTime Sync DAB SETPart list Installation/connectionBasic procedure KDC-DAB41U onlyAbout Bluetooth unit Optional ¤CAUTIONWiring connection SMB DAB ANTPin Color and function Before attaching, make Installing the unitRemoving the unit Firmly in placeInstallation the DAB antenna KDC-DAB41U only Installation overviewIt may not be possible to install on some type of vehicle Determining the antenna installation location Antenna InstallationSide Select the DAB antenna power Set Initial SET DAB ANT Power to on in Standby mode.Interior part Clip Troubleshooting Symptom Remedy/CauseBluetooth Phone book or the SMS disconnects the sound DAB ANT Error appearsDiscontinuous DAB reception is poorSpecifications Marking of products using lasers Class Laser Product
Top Page Image Contents