Alpine PXA-H701 owner manual Installation and Connections, Do not Splice Into Electrical Cables

Page 31

Installation and Connections

Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use.

Warning

DO NOT DISASSEMBLE OR ALTER.

Doing so may result in an accident, fire or electric shock.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR

STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

USE THE CORRECT AMPERE RATING WHEN

REPLACING FUSES.

Failure to do so may result in fire or electric shock.

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, shift lever, brake pedals, etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT INSTALL THE MONITOR NEAR THE

PASSENGER SEAT AIR BAG.

If the unit is not installed correctly the air bag may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and injuries.

DO NOT BLOCK VENTS OR RADIATOR PANELS.

Doing so may cause heat to build up inside and may result in fire.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE

STEERING WHEEL OR SHIFT LEVER.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

30-EN

Image 31
Contents PXA-H701 Before using Contents Still Hear Outside Noise While Driving Precautions Basic Operation Turning the power on and offAbout indicators Setting the speakersAdjusting the volume, balance, fader and subwoofer Using with Ai-NET connectionsSwitching the input Adjusting the input levelYES no Automatic AdjustmentsError Concrete examples Settings/AdjustmentsR / P H a S E L F 1 R R Bass Focus Settings/AdjustmentsTime difference Table Example of Steps 4 and 5 SettingGraphic equalizer adjustments Settings/AdjustmentsAdjustable frequencies Q P F r o n t L N D 3 5 k H z + 7 d B Parametric equalizer adjustments14-EN Over 16-EN Over adjustmentHints for adjusting the high range Hint for adjusting the subwooferHint for adjusting the low range MX settings 19-EN Using the Pro Logic II mode Using Dolby SurroundAdjustment procedure for Dolby Surround 22-EN Adjusting the speaker levelsMixing bass sound to the rear channel Adjusting the level for individual speakers manualAdjusting the acoustic image Using Dolby SurroundAdjusting the DVD level Achieving powerful high volume soundConvenient Functions Linear PCM settingMX mode setting Ai-NET connection Display settingsDefeat mode Storing settings in the memoryCalling out stored values Press the Disp button to select the desired display mode Switching the display modeDo not Splice Into Electrical Cables Installation and ConnectionsDo not Install in Locations with High Moisture or Dust PrecautionsTo prevent external noise from entering the audio system AccessoriesInstallation using Velcro fastener InstallationFlush Mounting the control unit Velcro Fastener Mounting Mounting the base unitTerminal specifications Connect to Basic Connections DiagramExamples of system expansion Please observe the following when using Fiber Optic Cable38-EN PXA-H701 + Head Unit + Video Deck etc. + External Amplifier 40-EN Terminology InformationCase of difficulty Others1set SpecificationsDimensions Components Parts name QuantityGERÄTE-PASS Händlerstempel Appendix Q9 no Luftport
Related manuals
Manual 48 pages 48.37 Kb