Kompernass KH 2391 Preparation / Installation, Removing the control panel from the car radio

Page 9

Preparation / Installation

1 x Stripping tongs or cable stripping knife 1 x Screwdriver

1 x SW 8 spanner (jaw size 8 mm) 1 x Ballpoint pen

For the connection of an aerial installed in the vehicle you may require :

1 x Aerial adapters (in accordance with the technical data of the aerial)

For the connection of an amplifier you will require:

2 x Cinch connection cables (insulation and plug: white / red)

each case. Store the installation keys ircarefully for future use.

Remove the DIN assembly bracket iqand place it flush in the DIN assembly cut-out of the vehi- cle‘s instrument panel.

Secure the DIN assembly bracket iqagainst removal. Bend approximately ten tin dog points on both the upper and lower side of the DIN assembly bracket iqfrom the inside towards the outside. Please ensure that the DIN assembly bracket iqis installed flush in the DIN assembly cut-out.

Attached the plastic frame 2completely to the front of the device ct.

LInstallation

LRemoving the control panel from the car radio

Avoid hard contact with the display window 9.

Press the “Open” button 4and allow the control panel 1to reach the horizontal position.

Push the control panel 1slightly to the left and pull it forwards.

Store the control panel in the plastic box (see also the illustration in the section „Attaching the Control Panel“).

LInstalling the DIN assembly bracket in the vehicle‘s instrument panel

Remove all packing material from the device.

Unscrew the safety transport screws gpcom- pletely from the metal housing du(see Fig. E) and carefully release the plastic frame 2from the front of the device ct.

Release the attachment points by slightly raising the upper frame edge and pulling it carefully towards the front.

Push the two installation keys irbetween the metal housing duand the preassembled DIN as- sembly bracket iquntil they clearly lock in place. Ensure that the convex side faces outwards in

L Connecting to the loudspeakers of the vehicle

Tip! Use an ISO plug.

Guide the connection cables of the loudspeakers mounted in the vehicle carefully out of the front of the DIN assembly bracket iq.

Establish the connection between the connection cables of the ISO plug and the connection cables of the loudspeakers fitted to the vehicle with the help of biscuit connectors, ensuring that the connections in the biscuit connectors do not cause any short circuits and that the fixing screws are firmly tightened.

Connect the lead of the plug-in emto the lead (+) for the rear right loudspeaker.

Connect the lead of the plug-in ento the lead (-) for the rear right loudspeaker.

Connect the lead of the plug-in eoto the lead (+) for the front right loudspeaker.

Connect the lead of the plug-in epto the lead (-) for the front right loudspeaker.

Connect the lead of the plug-in eqto the lead (+) for the front left loudspeaker.

Connect the lead of the plug-in erto the lead (-) for the front left loudspeaker.

Connect the lead of the plug-in esto the lead (+) for the rear left loudspeaker.

Connect the lead of the plug-in etto the lead (-) for the rear left loudspeaker.

GB/IE 11

KH2391_Content_UK.indd 11

05.09.2006 14:49:11 Uhr

Image 9
Contents GB / IE Operation and Safety Notes Hshm Imho Ilhu Hphq Ipioin Installation SafetyIntroduction OperationCar Radio KH For your safetyTechnical Data Introduction Scope of Supply Introduction / Safety Important Safety InstructionsAudio Storage Media Safety · Do not subject the device to any mechanical loadsTip! What course of action you should follow Preparation Safety / PreparationRemoving the control panel from the car radio Preparation / InstallationFor the connection of an amplifier you will require Tip! Use an ISO plugConnecting an amplifier InstallationConnecting to the vehicle‘s 12 V DC power supply Tip! Use an ISO PlugConnecting a portable audio device Attaching to DIN assembly bracketConnecting to the aerial of the motor vehicle Attaching the control panelSwitching off Installation / OperationSwitching on Selecting and adjusting the soundSelecting and adjusting playback functions OperationMult ON / OFF Function not possible on the KH Setting the 3-Band PLL Tuner Setting the volumeSeek 1 / 2  Mute FunctionManual Radio Station Search Press the Scan button cmPAU -button bu INT -button bt Playing Back the Stored StationsPlaying Back Audio Storage Media Operation Selecting Tracks on the Basis Storage Location Accessing Track PassagesSearching for Tracks from Folders Searching for Tracks by the File NameScanning RepeatRandom Playback RemovalOperation / Remote Control / Troubleshooting Remote ControlTroubleshooting Troubleshooting / Care and Maintenance / Disposal Care and MaintenanceDisposal Information Important Guarantee InformationImporter Kompernass GmbH Burgstr Bochum Germany24 GB/IE MP3 Car Radio GarantiekarteKH2391ContentUK.indd 05.09.2006 144922 Uhr GB/IE 28 GB/IE