Pin No. | Pin Name | I/O | Function |
61 | LOAD IN | O | Tray loading motor control signal, “L”:Loading |
|
|
|
|
62 | LOAD OUT | O | Tray loading motor control signal, “L”:When OPEN |
|
|
|
|
63 | BD.RESET | O | IC reset signal for CD control, “L”:RESET |
|
|
|
|
64 | LIGHT | O | BLUE LED control port of front panel, “L”:LED ON |
|
|
|
|
65 | SDATA | O | Serial data for SOUND PROCESSOR IC101 (M62428AFP) |
|
|
|
|
66 | SCLOCK | O | Serial clock for SOUND PROCESSOR IC101 (M62428AFP) |
|
|
|
|
67 | SLAT1 | O | Chip select for SOUND PROCESSOR IC101 (M62428AFP) |
|
|
|
|
68 | MUTE1 | O | Audio mute signal, “H”:Power amplifier ICs (IC801, IC851) MUTE |
|
|
|
|
69 | MUTE2 | O | Audio mute signal, “L”:Line mute (Q141, Q241) MUTE |
|
|
|
|
70 | STANDBY LED | O | Signal controlling LED which lights when power is OFF, “L”:LED ON |
|
|
|
|
71 | VSS0 | – | Ground potential of port |
|
|
|
|
72 | ON LED | O | Signal controlling LED which lights when power is ON, “L”:LED ON |
|
|
|
|
73 | TIMER LED | O | Signal controlling LED which lights in timer standby, “H”:LED ON |
|
|
|
|
74 | – | I | Not used |
|
|
|
|
75 | FL DISP SW | O | Power ON/OFF signal for FL display, “H”:FL display ON |
|
|
|
|
76 | SP RELAY SW | O | Speaker relay control signal, “L”:Speaker relay ON |
|
|
|
|
77 to 80 | – | I | Not used |
|
|
|
|
81 | ON/XSTBY | O | System power control signal, “H”:Standby relay ON |
|
|
|
|
82 | STEREO | I | Tuner stereo signal, “L”:Stereo |
|
|
|
|
83 | TUNED | I | Tuner selection OK signal, “L”:TUNED |
|
|
|
|
84 | ST IDATA | I | Serial input data for tuner |
|
|
|
|
85 | ST ODATA | O | Serial output data for tuner |
|
|
|
|
86 | ST.CLOCK | O | Serial clock for tuner |
|
|
|
|
87 | ST LATCH | O | Chip select for tuner |
|
|
|
|
88 | ST MUTE | O | Tuner mute output |
|
|
|
|
89 | ST POWER | O | Tuner power signal (Not used) |
|
|
|
|
90 | SIRCS | I | SIRCS code input signal (Remote control signal input) |
|
|
|
|
91 | PCL | I | 32 KHz clock monitor out |
|
|
| 32.768 kHz signal is output in the test mode (Refer to page 12.) |
|
|
|
|
92, 93 | – | I | Not used |
|
|
|
|
94 | DEST1 | I | Destination differentiation signal (Fixed at “H”) |
|
|
|
|
95 | DEST2 | I | Destination differentiation signal (Fixed at “L”) |
|
|
|
|
96 | – | I | Not used |
|
|
|
|
97 | HP MUTE | O | HP mute signal output |
|
|
|
|
98 | O | MD REC OUT control signal “L”:MD REC OUT MUTE (“L” only for MD function) | |
|
|
|
|
99 |
| O | REC OUT control signal of TAPE |
|
|
| “L”:TAPE REC OUT MUTE (“L” only for TAPE function) |
|
|
|
|
100 | V/T | O | Function control signal “H”:TAPE, “L”:CS/BS |
|
|
|
|
– 55 –