E P a R a T IO N C o n t, S T a L L a T IO N

CAMERA Power On/Off Zoom Lever Focus Exposure Program AE Shutter Speed White Balance Steady Shot Built-in Flash

SETTING

– Camera (On)

– Wide Angle Setting

– Auto Mode

– 1/60 Normal

– Auto Mode (see section)

– Off

P R E P A R A T IO N C o n t .

OPTIONAL WIDE ANGLE LENS__________________________________________

The housing’s port accepts optional 67mm threaded waterproof Wide-Angle lenses such as the Ikelite #6420W-20, Epoque DCL-20 and Inon UWL-100 Type 2 and Sea&Sea (58070). These waterproof lenses secure to the outside of the lens port.

Should you elect to use the optional Ikelite #6420 W-20, Epoque, Inon or Sea&Sea lens, carefully thread the waterproof lens on the front of the lens port. The lens threads are very fine; DO NOT cross thread. It should screw on very easily. If it is difficult to turn, you are cross threading.

INTERNAL WIDE-ANGLE LENS OPTION ________________________________________

Special ports are availab le for use wit h the Raynox HD- 5050 Pro high definition wide-angle l ens. optional por ts sold separately as dome port #9304 or flat lens port #9304.1. Raynox HD-5050 Pro lens not included. Lens not available for purchase through Ikelite .

FINAL PREPARATION_________________________________________________________

Remove the lens cap and cord from the cam era. Otherwise, they may interfere with the housin g seal.

The came ra's auto focus featur e is utilized und erwater. For be st results, move in close to your subject and use the wide angle range to shoot thr u as little water as possible. The f ull zoom range is accessible underwater.

Turn the c amera’s built-in flash OFF. Chart shows recommended initial settings underwater.

WHITE BALANCE_____________________________________________________________

Initially set the white balance to Auto. Use the Joy stick contr ols on the housing to change white balance.

Color Filter: When using th e color filter (during t he day) , set camera white balance to Indoor for 0 -15 foot depth. For 15-80 foot depth, set white balance to Outdoor. Video-Lite: When using optional V ideo Lite at NIGHT, set t he camera white balance to the Indoor p osition. During the DAY, use the Outdoor setting fo r subjects beyond 4-5 feet and t he Indoor settin g for close r subjects.

IN S T A L L A T IO N

CAMERA TRAY________________________________________________________________

The camera mounts to the tray, which extends from the back plate

of the housing. DO NOT remove the tray from the back plate.

O’ring

Position the camera against the two

Internal Lens Shade

Back Plate

stabilizing pins on the tray and secure with

the camera mounting bolt. The camera

should fit easily on the tray and should

be parallel with the sides of the tray.

Make certain that the lens shade has been

threaded completely into the camera to avoid

any potential clearance or sealing problems when

the camera is installed and the housing is se aled.

Stabilizing

Camera Tray

INSERTING THE CAMERA

Pins

Camera Mounting Bolt

Check that the o’ring is clean and properly positioned on the lip of the clear housing back plate. Check that the lens shade is com pletely threaded into the camera.

Once the camera is mounted to the tray as shown above, pull the housing controls out to provide clearance for installing the camera. Make sure the lens shade on the front of the camera fits into the port recess in the front of the housing.

DO NOT force this installation; the camera and t ray should slide easily into place so the housings back plate o’ring is resting against the m ain housing body. In this position the lid snaps can be positioned over the lid hooks on the housing back plate and snapped into position to seal the housing.

HOUSING CONTROLS________________________________________________________

Slide the housing controls back in place making sure they properly align with the camera functions.

Operate each control to see how it works with the camera. Some controls such as start/stop will be used frequently. Other controls may seldom be utilized. Refer to your camera owner's manual for the proper function of each camera control. Look thru the back to be sure that you can see into the viewfinder.

When using the housing controls, especially the start/stop,do NOT use excessive force because you could damage the camera.CAUTION

Remove the lens cap and cord from the camera. Otherwise, the cord may interfere with the hous ing seal.

If the housing controls are not properly positioned, they could interfere with the housing seal.

MANUAL FOCUS OPERATION_______________________________________________

Manual focus may be preferred in low light levels or when the subject possesses little contrast. Set the focus switch to Manual to c ancel the auto focus. If you want to manually adjust the focus, rotate the manual focus control as desired. To reacti- vate the auto focus, set the focus switch to Au to.

IKELITE UNDERWATER SYSTEMS

50 West 33rd Street • PO Box 88100 • Indianapolis, IN 46208 USA • 317.923.4523 Email: ikelite@ikelite.com • www.ikelite.com

6080-01-0208