Panasonic SLDZ1200, RQT7114-2Y Using with other equipment, Start play using the mixer’s fader

Using with other equipment

Before use

•Switch [PLAY SELECT] to select the media to be used

•Turn [MODE] on the rear panel to TURNTABLE

•Insert the SD Memory Card or CD to be used

Start play using the mixer’s fader

You can instantly start play from the auto cue point or cue point on this unit using the mixer’s fader by connecting this unit to the control ter- minal of a DJ mixer using a control cable connection. ( page 8)

Before use :

•Adjust buttons and control knobs of CH1 and CH4 on the DJ mixer so mixed sound is output from the master output.

•Turn the DJ mixer’s FADER START CH1 and CH4 to on.

•On unit 1 or 2, set the auto cue point or set the cue point and select the cue bank.

Starting with the channel fader

(e.g.) When the fader operation switch on the DJ mixer is set to NORMAL

1.On the DJ Mixer, change the C.FADER ASSIGN A switch to other than 1 and change the C.FADER AS- SIGN B switch to other than 4

2.Push the CH1, CH4 channel fader all the way to the bottom

3.During play or while paused on unit 1 or 2, press [CUE STOP] (Back cue)

•Returns to the set point and pauses.

4.When you want to start play, push the CH1 or CH4 channel fader up

•At the same time, play begins from the set point on unit 1 or 2.

•After you return the channel fader to its original position, unit back cues, and pauses after returning to the set point.

Starting with the cross fader

(e.g.) When the cross fader operation switch on the DJ mixer is set to NORMAL and to start play on CH1

1.On the DJ Mixer, change the C.FADER ASSIGN A switch to 1 and change the C.FADER ASSIGN B switch to 4

2.Push the cross fader all the way toward CH4 ()

3.During play or while paused on unit 1, press [CUE STOP] (Back cue)

4.When you want to start play, push the cross fader in the opposite direction indicated in step 2, towards CH1 ()

•At the same time, play begins from the set point on unit 1.

•You can alternate play by back cueing unit 2 connected to CH4.

Push the cross fader all the way toward CH4	Play CH4
	CH1 Back cue
Push the cross fader all the way toward CH1	Play CH1
	CH4 Back cue

Using two units for relay play

You can relay play by connecting the control terminals of the two units. ( page 9)

Before use:

•Turn Auto Cue on for both units, set the auto cue point for the track to be played and back cue.

Press [PLAY/PAUSE] on the unit to be played first

•Once track play finishes on the unit being played, play auto- matically begins from the unit on standby.

•The unit that was played first pauses and cues at the next track’s auto cue point.

•You can automatically alternate play between both units by repeat- ing this method.

•You can listen to many different tracks by changing the media and selecting the track of the unit in the standby position.

•Set the cue point, select the cue bank and back cue on the standby unit to begin relay play from the desired point of the desired track.

Note

•During play, if power on one of the units is cut or turned off, play may begin on the other standby unit.

•You cannot use fader start and relay play at the same time.

Using the amplifier and other equipment

Connect with the matching input terminals on the equipment (not in-
cluded). ( page 9)
•When using this unit’s DIGITAL OUT terminal, SD Audio is not out-		functions
put.
1	Put the equipment on standby
2	Press [PLAY/PAUSE] to play	Other
	•Audio played from the connected equipment is output.

23

RQT7114