AT&T 555-600-736 manual Introduction to Trunking Concepts, TIP and Ring Explained

Page 4

-2-

INTRODUCTION TO TRUNKING CONCEPTS

The way lines and trunks have been used to meet customers’ needs over past decades is rapidly changing. T-1, ISDN technology, fiber optics, and other advances in telecommunications are forcing us to rethink what lines and trunks should be used for a PBX or Key system. It is critical, however. that everyone involved in giving customers the most advanced, yet economical. system have a basic understanding of the concepts which are the foundations for sending and receiving telephone voice and data messages.

The goal of this Application Note is to explain the various types of lines and trunks which may connect to the MERLIN LEGEND Communications System. The Note focuses on the concepts of each type of line or trunk. While it also covers major interactions between the LEGEND system and the various lines/trunks, it is not aimed at explaining everything needed to install, initialize. and maintain them on the system. This is fully covered in the LEGEND System Installation, Programming, and Maintenance Manual. Additional information on lines and trunks may be found in the LEGEND PBX and Key Systems Planning Guides, as well as the Systems Reference Manual.

TIP AND RING EXPLAINED

The terms “Tip” and “Ring” occur inevitably in any description of telephone lines and trunks.

These terms originated in the early days of telephony when telephone connections were made by an operator who inserted a plug into a jack. This plug was similar to the plug on a set of conventional stereo headphones in that it had three conductors. These conductors were the “Tip,” corresponding to the tip of the plug. the “Sleeve,” the longest Conductor at the base of the plug, and a ring of metal between the Tip and the Sleeve called “Ring.”

The Sleeve was connected to a local electrical ground at the subscriber's premises and did not carry a signal to the telephone company Central Office (CO). The Tip and Ring conductors each connected to a wire that carried signals to the central office.

The terms became solidly embedded in telephone jargon and are still used in modem, electronic switching even though the actual “tips” and “rings” have long since disappeared. Today the terms Tip and Ring are used primarily as means for people in different places to identify precisely where each individual wire in each pair of wires (in a huge bundle of wires) needs to be connected. When a pair of wires is reserved for service as a trunk, one wire is designated Tip and the other wire is designated Ring.

During the process of ordering telephone service, a line assigner at the local operating company will reserve a pair of wires for each line or trunk ordered. Each individual wire in the bundle is identified by a unique color or combination of colors. Each trunk will have one color-coded wire assigned as the Tip lead and one color-coded wire assigned as the Ring lead of that particular trunk. For instance, a cable might contain one solid blue wire which would be reserved as the Ring lead on a given trunk, and one blue-and-white striped wire which would be reserved as the corresponding Tip lead for that same trunk. The line assigner will then furnish this information to installers at the customer’s premises and technicians in the central office. In this way technicians can coordinate their installation work and make the proper connections between the customer’s telephone equipment and the operating company’s central office.

Image 4
Contents AT&T Merlin Legend Communications System Application Notes Page Merlin Legend Trunking Concepts Application Note Index Introduction to Trunking Concepts TIP and Ring ExplainedLines and Trunks LOOP-START Trunks Operations LOOP-START Trunks POTENTIAL-PROBLEMS Problem of GlareAutomated Attendant Ghost Calls and Loop-Start Facilities Proper Loop-Start Facility Applications LOOP-START Trunks When to USE LOOP-START TrunksUnavoidable Loop-Start Facility Applications Cost GROUND-START Trunks Operations GROUND-START Trunks Potential Problems GROUND-START Trunks When to USE GROUND-START TrunksDirect Inward Dialing did Trunks Operational Characteristics Did Trunk Signaling Characteristics Types of Loop Reverse-Battery SignalingAdministration Considerations in Using did Trunks TIE Trunks When to USE did TrunksSimple Tie Trunk Operation Tandem Tie Trunk Operation TIE Lines Signaling and ImplementationTransferring Calls P E Transmit C E I V E ON-HOOK OFF-HOOK OFF Premises Stations Page DS1 Service Overview and OperationsDESIGN, Signaling & Implementation Potential Problems/LimitationsData Communications Equipment Do GBS Customers Need T-1?Channel Service Unit CSU Multiplexer MUX DS1 Facility Services IsdnSDN SID/ANI Special HOTEL/MOTEL Trunks Maintenance and TroubleshootingOperation Overview Hardware Module LINE/TRUNK Station Type Specifications TTR Trunk analog voice Reusable Modules from Merlin II R3 Administration ConsiderationsReferences