Weslo WCTL26080 Maintenance and TROUBLE-SHOOTING, Problem The power turns off during use

Page 12

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-888-963-4266, Monday through Friday, 8 a.m. until 6:30 p.m. Eastern Standard Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppres- sor is plugged into a properly grounded outlet (see page 7). Use only a CUL-listed surge sup- pressor, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the con- sole.

c. Check the circuit breaker located on the treadmill frame near the power cord. If the switch pro- trudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 6 on page 6. Most problems are the result of drained batteries.

b. If the speed display does not show a correct read- ing, remove the key and UNPLUG THE POWER CORD. Remove the screws from the sides and front of the hood. Carefully remove the hood. Locate the Reed Switch (19) and the Magnet (18) on the left side of the Pulley (89). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 3mm (1/8”). If necessary, loosen the Screw (44) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood and run the treadmill for a few minutes to check for a correct speed reading.

3mm

89

19

 

 

18

44

 

Top

 

View

 

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents
QUESTIONS? Model No. WCTL26080 Serial NoCustomer HOT Line Table of Contents Important PrecautionsPage Before YOU Begin FrontBack Right SideAssembly Tighten all parts used in assembly step Inset drawingThat the notched end of the Frame Guide is at Bottom Ends of the batteries touching the springs. CloseOperation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Diagram of the Console Step by Step Console OperationFollow your progress with the monitor display Measure your pulse, if desiredHOW to Fold and Move the Treadmill HOW to Select Kilometres and MilesHOW to Change the Incline of the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USEMaintenance and TROUBLE-SHOOTING Problem The power turns off during usePage Conditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part LIST-Model No. WCTL26080 Qty DescriptionRemove this Exploded Drawing and Part List from the Manual Exploded Ordering Replacement Parts Limited WarrantyIcon of CANADA, 900 de l’Industrie, St. Jérôme, QC J7Y 4B8
Related manuals
Manual 19 pages 24.55 Kb