Weslo WETL01540 user manual Assembly, Included hex key and wrench, View from, Beneath

Page 4

ASSEMBLY

The help of a second person is recommended. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires only the

included hex key and wrench

.

1.Identify the Right Upright (36), which has a single hole in the indicated location. Hold the Right Upright against the Base (14) as shown, and orient the Right Upright so the two indicated holes are on the side shown.

Attach the Right Upright (36) to the Base (14) with two M8 x 50mm Bolts (38), two M8 Curved Washers (37), and two M8 Nylon Nuts (13) as shown. Make sure that the Curved Washers are turned so they conform to the curve of the Base. Do not tighten the Nylon Nuts yet.

Attach the Left Upright (35) to the Base (14) in the same way. Make sure that the Left Upright is oriented so the two indicated holes are on the side shown. Do not tight- en the Nylon Nuts yet.

2.Raise the Left Upright (35) and the Right Upright (36) to the position shown. Place the front of the Frame (29) between the Left Upright and the Right Upright. Connect the Reed Switch Wire (6) to the Short Reed Switch Wire

(A).

3.Attach the Hood (28) to the front of the Frame (29) with two M5 x 10mm Bolts (10).

4.See drawing 4a. Locate the small incline knob on each side of the Frame (29). Slide the knobs into one of the three sets of slots in the brackets on the Uprights (35).

Make sure that the knobs are fully inserted at the same height.

Look under the Frame (29) near the Left Upright (35). See drawing 4b. Locate the Clip (11) attached to the underside of the Frame. Insert the Reed Switch (6) into the Clip as shown. Next, locate the Magnet (12) on the left Flywheel (9). Turn the Flywheel until the Magnet is aligned with the Reed Switch. Move the Reed Switch so that there is a 3 mm (1/8 in.) gap between the Reed Switch and the Magnet. Then, tighten the M4 x 12mm Screw (3) in the Clip.

1

 

 

 

Holes

 

 

 

 

 

 

 

 

36

 

 

 

37

 

 

 

Hole

 

 

 

 

 

 

 

14

Holes

 

 

 

 

 

 

13

 

35

 

38

37

37

 

 

 

 

 

 

 

 

 

 

 

 

 

 

38

 

13

 

 

 

 

 

 

 

 

 

 

37

 

2

 

 

29

36

 

 

 

 

 

 

 

6

 

 

 

35

 

 

 

 

 

 

 

A

 

 

 

3

 

 

 

 

 

 

 

 

28

 

 

 

 

 

 

 

29

 

 

 

 

 

10

4a

 

35

4b

View from

 

 

 

beneath

 

 

Knob

 

 

 

 

9

Bracket

 

 

 

 

 

 

 

 

29

 

 

 

 

11

 

 

 

 

3

 

 

 

12

6

29

 

 

 

 

 

 

 

 

 

1/8”

 

4

Image 4
Contents 8457 089 QUESTIONS?Model No. WETL01540 Serial No Table of Contents Important PrecautionsBefore YOU Begin Assembly Included hex key and wrenchView from BeneathPage Lubricating the Walking Platform Treadmill OperationSTEP-BY-STEP Console Operation Folding the Treadmill for Storage Incline AdjustmentLowering the Treadmill for USE Maintenance and Troubleshooting Symptom the Console does not Function ProperlySymptom the Walking Belt does not Move Smoothly Symptom the Walking Belt Slips or is OFF-CENTREWHY EXERCISE? HOW to Measure Your Heart RateConditioning Guidelines Exercise IntensityExercise Frequency Part LIST-Model No. WETL01540Qty Description Exploded DRAWING-Model No. WETL01540 R1004AOrdering Replacement Parts 08457 089