Sears 831.297432 owner manual TROUBLE,SHOOTING and Storage, Symptom the Power does not Turn on

Page 10

TROUBLE,SHOOTING AND STORAGE

Most treadmill problems can be solved by following the simple steps below. Find the symptom that ap- plies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736- 6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

1.SYMPTOM: THE POWER DOES NOT TURN ON

a.Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into a propedy grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page 7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. (See HOW TO TURN ON THE POWER on page 8.)

c. Check the circuit breaker located on the treadmill near the

 

 

power cord. If the switch protrudes as shown, the circuit

 

 

breaker has tripped. To reset the circuit breaker, wait for five

Tripped _

I Reset

minutes and then press the switch back in.

 

 

2. SYMPTOM: THE POWER TURNS OFF DURING USE

 

 

a. Check the circuit breaker located on the treadmill near the power cord. If the circuit breaker has tripped (see the drawing above), wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

3.SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON

a.Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b.If the walking belt is overtightened, treadmill performance may decrease and the walking belt may be permanently damaged. Remove the key and UNPLUG THE POWER CORD. Using the 3/16" allen wrench, turn both rear roller adjustment bolts coun- terclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 3-4inches off the walking platform. The center of the walk- ing belt should just touch the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert

the key and run the treadmill for a few minutes. Repeat until the

Rear Roller Adjustment Bolts

walking belt is properly tightened.

 

c. If the walking belt still slows when walked on, please call our toll-free HELPLINE.

4.SYMPTOM: THE WALKING BELT IS OFF-CENTER OR SLIPS WHEN WALKED ON

a.If the walking belt has shifted to the left, first remove the key and UNPLUG THE POWER CORD. Using the 3/16" allen wrench, turn the left rear roller adjustment bolt clockwise, and the right bolt counterclockwise, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, in- sert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents EX Panse SEARS, Roebuck and CO., Hoffman ESTATES, ILIfull 90 DAY Warranty SEARS, Roebuck and CO., Dept WA Hoffman ESTATES, ILTable of Contents ExpanseImportant Precautions Front Before YOU BeginBack Right SideAssembly Assembly is completedPerformant Lube TM Walking Belt Operation AdjustmentHOW to Plug Power Cord Performant Lube TMControlling the Speed Installing BatteriesHOW to Turn on the Power Motivational Fitness MonitorHOW to Change the Incune of the Treadmill Turning OFF the PowerPadded Walking Platform Symptom the Walking Belt Slows When Walked on Symptom the Power does not Turn onSymptom the Power Turns OFF During USE TROUBLE,SHOOTING and StorageUnplug the power cord when the treadmill is not in use StorageUnconditioned Conditioned Training Zone AGE BEATS/MIN Conditioning GuidelinesExercise Intensity Workout GuidelinesQuadriceps Stretch Suggested StretchesHamstring Stretch Inner Thigh StretchPart LIST--Model R0296A NSPExploded DRAWING--Model No RO296A £/ARS SEARS, Roebuck and CO., Hoffman ESTATES, IL 60179 USA
Top Page Image Contents