Keys Fitness 4500T owner manual Calibration Sequence

Page 20

Calibration Sequence

Do not attempt to calibrate the treadmill unless an Error Code is present. See Error Messages (page 23). Our treadmill is equipped with a software package that will perform a calibration sequence unique to your specific model number.

Please perform the following steps to calibrate the Keys 4500T Treadmill.

1.Unplug power cord from outlet strip.

2.Attach Safety Key to console.

3.Plug power cord into outlet strip.

4.Initiate calibration sequence. Locate the hole on the back of the console and insert the eraser end of a pencil through the hole and press the calibration switch twice. As shown on page 19.

5.CL21 should appear in the Time window, if not, continue to press the calibration switch until CL21 appears.

Note: During the calibration sequence, the Time window will display which step you are at in the process (C21, C22, C23 and so on). The CAL/DIST window will display which key should be pressed next. For example, “E” for Enter, “P” for Power, or “SS” for Start / Stop.

6.CL21: MPH or KPH will be flashing in the Speed window, pressing the Speed +/ - button will toggle options. Choose MPH (KPH), press Enter.

7.CL22: 8, 10, or 12 (13, 16, or 20 in KPH mode) will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose 10 (or 16 for KPH mode), press Enter.

8.CL23: FFF, UUU, or HHH will be displayed in the Speed window, pressing the Speed +/ - button will tog- gle options. Choose UUU, press Enter.

9.CL24: 111 or 222 will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose 222, press Enter.

10.CL25: Verify “---” is displayed, press Enter.

11.CL26: OPA or OPI will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose OPA, press Enter.

12.CL27: Blank (nothing), “a”, “b”, “c”, “d” or “e” will be displayed in the Incline window, pressing the Speed +/ - button will toggle options. Choose “blank”, press Enter.

13.CAL/DIST window will display “55”. Press Start / Stop. “E” will display in CAL/DIST window.

14.Press Enter Program button.

15.At this time, make sure you are not standing on the walking belt, as the machine will automatically initiate belt movement and run through a complete calibration and diagnostic routine.

Press Enter. Belt will begin to move. Unit will begin self-calibration.

16.When Speed and Incline calibration has finished, press Power button twice, display should be blank, and treadmill should be ready for use.

To avoid possible damage to the treadmill and the possibility of injury, do not operate the treadmill until the problem is corrected. Call Keys Fitness Customer Service at (888)-340-0482 if problem per- sists.

20

Image 20
Contents Keys 4500T Treadmill Table of Contents Important Safety Information Safety Precautions and TipsBefore You Start Assembly Parts ListAssembly requires the included allen wrench Console Washer 9*22*2 Allen Bolt M8*15 Left Upright Attach the Left Junction Box as shown Congratulations Moving Instructions Power Requirements Console Panel Functions Time / Pace WindowQuick Start / Manual Mode Program OperationSpeed Program Profiles Monitoring Your Heart Rate Monitoring Your Heart RateTarget Heart Rate Zone Warm Up Exercises Exercise GuidelinesChange to MPH or KPH Calibration Sequence Belt Adjustment Maintenance Instructions To Apply Lubricant to the Walking BoardError Messages Treadmill Error MessagesTroubleshooting Guide Treadmill will not startParts List 4500t Treadmill Parts List Rev a4500t CE 220v Treadmill Parts List Rev a Exploded View Console Assembly Wire Harness 121 Exploded View Warranty Information Keys Fitness PRODUCTS, LP Limited WarrantyCustomer Service