Image IMTL41530 user manual Connectors should slide together easily, Console Base with two, Next

Page 8

5.Open part bag A. Hold the Pulse Bar (125) near the Console Base (85). Connect the Pulse Wire (124) on the Pulse Bar to the indicated wire on the Console Base.

The connectors should slide together easily and

snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try to connect them again. Insert the wires into the hole in the

Console Base.

Have a second person hold the Pulse Bar (125) firmly on

 

the Console Base (85). Attach the Pulse Bar to the

 

Console Base with two

1 1/4” Screws (92) in the loca-

tions shown. Be careful not to damage the Pulse

 

Wire (124) or the wire on the Console Base.

Next,

tighten two 2” Silver Screws (93) into the Console Base

 

and the Pulse Bar in the locations shown.

Note: The

correct Screws must be used in the correct loca-

 

tions, or the Pulse Bar may be damaged.

 

6.Identify the Left and Right Handrails (68, 81) (see the end views of the Handrails in the inset drawing). The

curved edges of the Handrails should be on the outside.

Slide the Right Handrail (81) onto the Right Handrail Bracket (113), and press the lip on the front of the Right Handrail under the Console Base (85). (Note: It may be helpful to tip the Right Handrail and to tap it with a rub-

ber mallet to correctly position it.) Tighten three 3/4” Screws (6) into the Right Handrail as shown. Note: It may be necessary to move the lower end of the Right Handrail slightly to align the lower screw hole.

Attach the Left Handrail (68) in the same way.

See assembly step 1. Tighten the four 1 1/4” Bolts (104).

7.Press the Latch Knob Sleeve (75) into the Left Upright (69). Note: It may be helpful to use a rubber mallet to fully insert the Latch Knob Sleeve.

Remove the Latch Knob (70) from the Latch Pin (80).

Make sure that the Latch Pin Collar (76) and the Spring

(77)are on the Latch Pin. (Note: If there are two Latch Pin Collars, place one on each side of the Spring.) Insert the Latch Pin into the Left Upright (69) and tighten the Latch Knob onto the Latch Pin.

5

 

 

 

93

 

92

125

 

 

 

 

124

 

124

93

85

 

 

 

 

92

6

 

 

68

 

 

6

 

 

 

Lip

85

Curved Edge

81

 

 

 

 

 

113

 

 

6

(81) (68)

 

 

7

 

 

70

 

 

 

77

 

75

76

 

 

 

 

80

 

69

 

 

8

Image 8
Contents QUESTIONS? Model No. IMTL41530 Serial NoTo Avoid Customer HOT LineTable of Contents Important Precautions Use the treadmill only as described in this manualSame circuit. Do not use an extension cord Never leave the treadmill unattended while itNever drop or insert any object into any open- ing Back Using the treadmillBefore YOU Begin Assembly If the Connectors are not Do not overtighten the Wheel BoltsLong PressConnectors should slide together easily Console Base with twoNext Pulse Bar in the locations shownWire With four 3/4 Screws 6 as shown. Note There areHold the receiver so the small cylin Der is near the lower edge of the receiver and is facHOW to Plug in the Power Cord Treadmill OperationPerformant Lube This product must be grounded.If it should malfuncConsole Diagram Features of the ConsoleWater bottle in the water bottle holder See VideoHOW to Turn on the Power HOW to USE a QUICK-FIT Speed Program Next period Important When the currentStart the program Cassettes HOW to Connect Your Portable CD PlayerHOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerCable Adapter Audio 5mm CableHOW to Connect Your VCR Audio Adapter CablePrograms HOW to USE Programs Directly from OUR WEB Site Information Mode MentProvides Hands-free op To purchase a chestHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USEPower Cord TroubleshootingSolution Plug the Power Cord Unplug the Power CordExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Key No. Qty Description Key No. Qty R0803C Exploded DRAWING-Model No. IMTL41530 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part No R0803C