Image IMTL315040 user manual Troubleshooting, Problem The power turns off during use

Page 23

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-800-753-4645, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The speed display on the console does not function properly

SOLUTION: a. Remove the key and UNPLUG THE POWER CORD. Remove the hood from the treadmill. Locate the Reed Switch (21) and the Magnet (43) on the left side of the Pulley (42). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap be- tween the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (62), move the Reed Switch slightly, and then retighten the Screw. Reattach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8” 62

21

Top

View

42

43

23

Image 23
Contents Customer HOT Line QUESTIONS?Model No. IMTL315040 Serial No Table of Contents Important Precautions Page Right Side Before YOU BeginBack Treadmill until it is completely assembled AssemblyMake sure that the power cord is not plugged Firmly tighten the Crossbar Bolts Be careful not to pinch the wiresTop View Page Performant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerHOW to USE Speed and Incline Programs Follow your progress with the displays HOW to Connect Your Portable CD Player HOW to Connect Your Computer HOW to Connect Your Home StereoHOW to Connect Your VCR Whenkey. the program is completed, remove Press the Play button on your CD player or VCRMeasure your heart rate, if desired Whenkey . the program is completed, remove HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start the program Information Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingKey and Unplug the Power CORD. Using Problem The walking belt slows when walked onExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Key Qty Description R0804AExploded DRAWING-Model No. IMTL315040 Exploded DRAWING-Model No. IMTL315040 Page 2 R0804A Exploded DRAWING-Model No. IMTL315040 Page 3 R0804A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT HOW to Order Replacement PartsLimited Warranty