Assembly, Handrail Bolts | NordicTrack NTTL11512 instruction

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench

and your own phillips screwdriver, adjustable wrench and wire cutters .

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the treadmill or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt or foot pads, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

1.With the help of a second person, carefully raise the Uprights (110) to the position shown.

Refer to the inset drawing. Insert one of the Extension Legs (88) into the treadmill as shown. Make sure that the Extension Leg is turned so the Thick Base Pad (90) is on the bottom. Note: It may be helpful to tip the Uprights (110) forward as you insert the Extension Leg.

Insert the other Extension Leg (not shown) in the same way.

2.With the help of a second person, carefully tip the Uprights (110) down as shown. Make sure that the

Extension Legs (88) remain in the Uprights.

Attach each Extension Leg (88) with two Base Screws (86) and a Base Pad (75) as shown.

With the help of a second person, carefully tip the Uprights (110) back to the vertical position.

Note: One replacement Base Pad (75) and Spacer (not shown) may be included. If a Base Pad becomes worn and needs to be replaced, use the replacement Base Pad. If a Thick Base Pad (90) needs to be replaced, use the replacement Base Pad with the Spacer.

3.Refer to drawing 3a. While another person holds the Handrails (89), thread Handrail Bolts (111) about 1” into the two holes in each Handrail. Then, remove the

Handrail Bolts.

Refer to drawing 3b. Pinch the tabs on the Grounding Bracket (115) so that the tabs will fit into the indicated hole in the left Upright (110). Then, insert the Grounding Bracket into the hole as far as possible.

Note: It may be helpful to set the Handrails (89) on the Uprights (110) and loosely thread a Handrail Bolt (111) into the left Upright and the left Handrail. Tip the Handrails, if necessary, to thread in the Bolt. Have an- other person support the Handrails as you complete the remaining steps.

1
		110
			110
			88
			90
2
	90	90
	90
			75
110		110
110		88	86
		88	86
75	86		90
	86
90	88
	88
3a
	89
		111
3b	115
	115	110
		110
		111

1
		110
			110
			88
			90
2
	90	90
	90
			75
110		110
110		88	86
		88	86
75	86		90
	86
90	88
	88
3a
	89
		111
3b	115
	115	110
		110
		111

1
		110
			110
			88
			90
2
	90	90
	90
			75
110		110
110		88	86
		88	86
75	86		90
	86
90	88
	88
3a
	89
		111
3b	115
	115	110
		110
		111

1
		110
			110
			88
			90
2
	90	90
	90
			75
110		110
110		88	86
		88	86
75	86		90
	86
90	88
	88
3a
	89
		111
3b	115
	115	110
		110
		111