INTRODUCTION
P R E - A S S E M B LY
A S S E M B LY STEP 2
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
CONDITIONING TROUBLESHOOTING LIMITED
GUIDELINES & MAINTENANCE WARRANTY
Disassemble box and remove the cardboard packaging that is not beneath the treadmill. Do not attempt to lift the treadmill at this time. Remove plastic wrap from console masts.
*Note: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.
A S S E M B LY STEP 1
HARDWARE BAG 1 CONTENTS :
BOLT (A) | FLAT WASHER (B) | NUT (C) |
60 mm | 8 mm | 8 mm |
Qty: 2 | Qty: 2 | Qty: 2 |
BOLT (D) |
|
|
| ARC WASHER (E) |
|
| |||
15 mm |
|
|
| 6 mm |
Qty: 1 |
|
|
| Qty: 1 |
|
| |||
|
|
|
|
|
FLAT WASHERS (B) | NUTS (C) |
| A | Open HARDWARE BAG 1. |
|
|
| ||
|
|
| B | Slide LEFT CONSOLE MAST over |
|
|
|
| MAIN FRAME BRACKET. |
|
|
| C | Insert 2 Bolts (A) on the bottom |
|
|
|
| outside of the mast and secure with |
LEFT CONSOLE MAST |
|
|
| 2 FLAT washers (B) and |
|
|
|
| 2 NUTS (C). |
|
|
| D | Insert BOLT (D) with ARC washer |
|
|
|
| (E) into front hole on the mast and |
|
|
|
| completely tighten. |
BOLTS (A) MAIN FRAME BRACKET | ARC WASHER (E) | BOLT (D) | E | Use flat wrench to completely |
|
|
| ||
|
|
|
| tighten nuts (C) inserted in Step C. |
HARDWARE BAG 2 CONTENTS :
BOLT (A) 60 mm Qty: 2
BOLT (D) 15 mm Qty: 1
CONSOLE CABLES | RIGHT CONSOLE MAST |
LEAD WIRE
RIGHT CONSOLE MAST | BOLTS (A) | CONSOLE CABLES |
MAIN FRAME BRACKET
ARC WASHER (E)
FLAT WASHERS (B)
BOLT (D)
NUTS (C)
FLAT WASHER (B) | NUT (C) |
8 mm | 8 mm |
Qty: 2 | Qty: 2 |
ARC WASHER (E)
6mm Qty: 1
APull LEAD WIRE through RIGHT CONSOLE MAST.
After pulling the lead wire through the mast, the top of the console cables should be located at the top of the mast.
Detach and discard lead wire.
BOpen HARDWARE BAG 2.
CSlide RIGHT CONSOLE MAST over
MAIN FRAME BRACKET.
*Note: Do not pinch CONSOLE CABLES when placing the mast onto the main frame.
DInsert 2 BOLTS (A) on the bottom outside of the mast and secure with 2 FLAT WASHERS (B) and 2 NUTS
EInsert BOLT (D) with ARC washer
(E)into front hole on mast and completely tighten.
FUse flat wrench to completely tighten nuts (C) inserted in Step D.
IMPORTANT PRECAUTIONS
ASSEMBLY
BEFORE YOU BEGIN
TREADMILL OPERATION
LIMITED TROUBLESHOOTING CONDITIONING WARRANTY & MAINTENANCE GUIDELINES
T1200_Treadmill_Rev.1.9.indd | 6/22/07 4:45:02 PM |