Cadence WLTL42570 user manual Maintenance and TROUBLE-SHOOTING, Symptom the Power does not Turn on

Page 16

m

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems follow the steps listed, free at 1-800-999-3756,

can be solved by following the steps below. Find the symptom that applies, and if furlher assistance is needed, please call our Customer Service Department tog- Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

1.SYMPTOM: THE POWER DOES NOT TURN ON

a.Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page 7) Use only a ULdisfed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b.After the power cord has been plugged in, make sure that the key is fully inserted into the console. (See step 1 on page g.)

c.Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. TO reset the clrcuit breaker, wait for five minutes and then press the switch back in.

2.SYMPTOM: THE POWER TURNS OFF DURING USE

a.Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tdppod, wait for five minutes and then press the switch back in.

b, Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console. (See step 1 on page 9.)

d If the treadmill still will not run, please call our Customer Service Department, toll-free.

3.SYMPTOM; THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY

a.Check the batteries in the console. See BATTERY INSTALLATION on page 8. Most problems are the result of drained batteries

h.Remove the six screws from the hood. Carefully remove the hood. Locate the Reed Switch (86) and the Magnet (67) on the left side of the Pulley (85). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8". If necessary, loosen the Screw (63) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

12

Image 16
Contents Model No. WLTL42570 NumberCustomer HOT Line Mon.-FrL, 6 a.m.-6 p.rn, MSTTable of Contents Page Before YOU Begin WaikinRtGHT Side CircuitHandrail Washer Handrai Screw AssemblyConsole pJate Screw Extension Leg Screw Wire Harness is not pinched HOW to Plug Power Cord Operation and AdjustmentPerformant Lube TM Walking Belt Barery Installation Diagram of the ConsoleMonitor Dispays Page Exploded DRAWiNG--Model No. WLTL42570 Page Qty DescripUon Speed HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillMinutes HOW to Move the Treadmill HOW to Lower the Treadmill for USEMaintenance and TROUBLE-SHOOTING Symptom the Power does not Turn onSymptom the Power Turns OFF During USE Make sure that the power cord is pluggedSymptom the Walking Belt Slows When Walked on Symptom the Walking Belt is OFF-CENTERWHEN Walked onFat Burning Aerobic ExerciseHigh Parfonnance Athletfo Conditioning Warm-upCool-down Inner Thigh StretchOrdering Replacement Parts Limited WarrantyModel Number of the Product WLTL42570 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT