Spirit EL 3 Elliptical, EL 5 Elliptical owner manual Assembly Instructions, Unpacking the Unit

Page 12

Assembly Instructions

￿UNPACKING THE UNIT

1.Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack.

2.Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately.

3.Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to avoid confusion.

STEP 1: REAR RAIL ASSEMBLY

1.Remove the hardware from the hardware pack for step 1. You should have four 3-3/4￿ X 3/8￿ bolts, four curved washers, two 2-1/4￿ X 3/8￿ bolts, two flat washers and six 5/8￿ X 1/4￿ Phillips head screws.

2.Put the two flat washers on the 2-1/4￿ bolts and hand-tighten them, through the top of the middle stabilizer tube, into the rear rail assembly.

3.Put the four curved washers on the 3-3/4￿ bolts and hand-tighten them through the front of the middle stabilizer tube, into the rear rail assembly.

4.Using the wrench provided tighten all six bolts securely.

5.Locate the four plastic covers (XE150, XE350 only) for the rear rail assembly and the one cover for the front stabilizer and install them using the six 5/8￿ X 1/4￿ screws and the Phillips head screw driver provided.

STEP 2: CONSOLE MAST ASSEMBLY

1.Remove the hardware from the hardware pack for step 2. You should have one 2-1/4￿ X 3/8￿ bolt, one lock washer, two 3/4￿ X 3/8￿ bolts, two curved washers and four 1/2￿ X 1/4￿ Phillips head screws.

2.Locate the console mast and console mast cover and slide the cover onto the mast as far as it will go. Make sure the cover is facing the correct way.

3.At the top opening of the main body of the elliptical is a wire harness. Unravel and straighten out the wire harness and feed it into the bottom of the console mast tube and out of the top opening.

4.Install the console mast into the receiving bracket in the top of the main body. NOTE: there is one bolt already installed in the receiving bracket that will engage with the slot at the bottom of the console mast. This needs to be tightened at the end along with the three other console mast bolts.

11

EL3 /EL5 Elliptical

 

Image 12
Contents Elliptical Table of Contents Product Registration Important Safety Instructions Important Electrical Information Important Operation InstructionsAssembly Pack Check List EL3 StepStep Tools Assembly Pack Check List EL5 Step Tools Assembly Instructions Unpacking the UnitHandle BAR Assembly Power Connector Located on FRONT, Left Hand Side of Unit Assembly Drawing EL3 EL3 /EL5 Elliptical Assembly Drawing EL5 EL3 /EL5 Elliptical Features TransportationGetting familiar with the EL3 control panel Power up Operation of Your EllipticalQuick Start mode Basic information and functionsProgramming the console Entering a program/Changing Settings Preset ProgramsManual Programs Fat BurnCardio StrengthInterval Custom User Defined ProgramsHeart Rate Control Program operation Getting familiar with the EL5 control panel Quick StartBasic information Entering/Changing Settings Hill Fat Burn Cardio Interval EL3 /EL5 Elliptical Heart Rate programs Rate of Perceived Exertion Using a Heart Rate Transmitter Erratic OperationHeart Rate Control Program 1 & 2 HR 1, HR 2 operation Maintenance Maintenance Menu in console softwareManufacturer’s Limited Warranty Elliptical Warranty