Spirit EL 5 Elliptical, EL 3 Elliptical owner manual Handle BAR Assembly

Page 13

5.Put the flat washer onto the 2-1/4￿ bolt and the two curved washers onto the two

3/4￿ bolts. Install, and hand tighten, the 2-1/4￿ bolt through the left side of the receiving tube into the console mast. NOTE: There is a wire running through the tube. Be careful not to damage or pinch this wire during this procedure. Damage to the electronic console could result. Install, and hand tighten, the two 1￿ bolts through the front of the receiving tube into the console mast.

6.Using the two sided wrench tighten the three bolts, and the fourth bolt which is pre-installed, firmly. These bolts should be tightened as much as you possibly can.

7.Locate the electronic console and the four 1/2￿ X 1/4￿ Phillips head screws.

8.There will be three electrical wire connectors at the top opening of the console mast, two 2 pin (hand pulse sensors), one 10 pin (main wire harness). Connect these to the mating connectors on the back of the console. The connectors are keyed so you cannot plug them in the wrong way so do not force them.

9.Storing the excess wire back into the console mast, carefully install the console onto the mounting plate and secure using the four Phillips head screws.

STEP 3: HANDLE BAR ASSEMBLY

1.Remove the hardware from the hardware pack for step 3. You should have two 5/8￿ X 3/8￿ bolts, two large flat washers, two large wave washers and six self tapping Phillips head screws.

2.Locate and install the two large wave washers onto the handle bar axle, one on each side.

3.Slide the left and right handle bars onto the appropriate side of the axle. There is a sticker on each handle bar indicating L for left and R for right.

4.Put the large flat washers onto the two 5/8￿ X 3/8￿ bolts and install, and tighten, in the threaded holes in the ends of the axle.

5.Install the plastic covers over the handle bar/axle connections with the six self tapping Phillips head screws.

STEP 4: FOOT PAD/CONNECTING ARM ASSEMBLY (This step may have already been performed at the factory on your unit)

1.Remove the hardware from the hardware pack for step 4. You should have two 1-1/4￿ X 5/16￿ bolts, two flat washers, two Nylon nuts, four 5/8￿ machine screws (long), four 3/8￿ machine screws (short) and two self-tapping Phillips head screws.

2.On the pedal arms, in the middle on top, there are two axles already installed in the bushing housings. Remove, from one side of each axle, the bolt (one should be loose) and washer. Remove the axle and set aside for the next step.

3.Locate the left foot pad/connecting arm. Holding the rear of the foot pad with your right hand and the connecting arm, just in front of the foot pad, with your left hand, place the foot pad over the bushing housing.

12

EL3 /EL5 Elliptical

 

Image 13
Contents Elliptical Table of Contents Product Registration Important Safety Instructions Important Operation Instructions Important Electrical InformationStep Assembly Pack Check List EL3Step Tools Assembly Pack Check List EL5 Step Tools Unpacking the Unit Assembly InstructionsHandle BAR Assembly Power Connector Located on FRONT, Left Hand Side of Unit Assembly Drawing EL3 EL3 /EL5 Elliptical Assembly Drawing EL5 EL3 /EL5 Elliptical Transportation FeaturesOperation of Your Elliptical Getting familiar with the EL3 control panel Power upBasic information and functions Quick Start modeProgramming the console Preset Programs Entering a program/Changing SettingsManual Fat Burn ProgramsStrength CardioCustom User Defined Programs IntervalHeart Rate Control Program operation Quick Start Getting familiar with the EL5 control panelBasic information Entering/Changing Settings Hill Fat Burn Cardio Interval EL3 /EL5 Elliptical Heart Rate programs Rate of Perceived Exertion Erratic Operation Using a Heart Rate TransmitterHeart Rate Control Program 1 & 2 HR 1, HR 2 operation Maintenance Menu in console software MaintenanceElliptical Warranty Manufacturer’s Limited Warranty