Gold's Gym GGTL03607.2 manual HOW to Turn on the Power, HOW to USE the Manual Mode

Page 13

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room tem- perature before turning on the power. If you do not do this, the console displays or other electrical components may become damaged.

Plug in the power cord (see

 

 

 

 

 

 

 

 

 

 

 

 

page 11). Next, locate the

 

Reset

 

 

 

 

reset/off circuit breaker on

 

 

 

 

 

 

 

 

 

 

the treadmill frame near the

 

Position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

power cord. Switch the cir-

 

 

 

 

 

 

 

 

 

 

 

 

cuit breaker to the reset po-

 

 

 

 

 

 

 

 

 

 

 

 

sition.

 

 

 

 

 

 

IMPORTANT: The console features a display demo mode, designed to be used if the treadmill is dis- played in a store. If the displays light as soon as you plug in the power cord and switch the reset/off circuit breaker to the reset position, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays remain lit, see THE INFORMATION MODE on page 16 to turn off the demo mode.

Next, stand on the foot rails of the treadmill. Find the clip attached to the key (see the drawing on page 12) and slide the clip onto the waistband of your clothes.

Then, insert the key into the console. When the key is inserted, the displays will light. IMPORTANT: In an emergency situation, the key can be pulled from the console, causing the walking belt to slow to a stop. Test the clip by carefully taking a few steps backward; if the key is not pulled from the console, adjust the position of the clip.

HOW TO USE THE MANUAL MODE

1.Insert the key into the console.

See HOW TO TURN ON THE POWER above.

2.Select the manual mode. When the key is in- serted, the manual mode will be selected. If a program has been se- lected, press the Classic Workouts but-

ton repeatedly until a track appears in the display.

3.Start the walking belt.

To start the walking belt, press the Start button, the Speed increase button, or one of the Speed but- tons numbered 2 through 10.

If you press the Start button or the Speed increase button, the walking belt will begin to move at 1 mph. As you exercise, change the speed of the walking belt as desired by pressing the Speed increase and decrease buttons. Each time you press a but- ton, the speed setting will change by 0.1 mph; if you hold down a button, the speed setting will change in increments of 0.5 mph.

If you press one of the nine numbered Speed but- tons, the walking belt will gradually increase in speed until it reaches the selected speed setting. To stop the walking belt, press the Stop button. The time will begin to flash in the display. To restart the walking belt, press the Start button, the Speed increase button, or one of the nine numbered Speed buttons.

4.Change the incline of the treadmill as desired. To change the incline of

the treadmill, press the Incline increase and de- crease buttons or one of the Incline buttons num- bered 0 to 10. Each time

you press the Incline increase or decrease button, the incline setting will change by 0.5%; if you hold down a button, the incline setting will change quickly. If you press one of the numbered Incline buttons, the treadmill will adjust to the selected in- cline setting. Note: After you press the buttons, it may take a moment for the treadmill to reach the selected incline setting.

5.Follow your progress with the display.

When the manual mode is selected, a track repre- senting 1/4 mile (400 meters) will appear in the upper right corner of the display. As you walk or run on the treadmill, the indicators around the track will appear in succession until the entire track appears. The track will then disappear and the indicators will again begin to appear in succession.

13

Image 13
Contents Please do not Contact QUESTIONS?On the WEB Table of Contents Important Precautions Treadmill is not in use. See the drawing on Before YOU Begin Assembly See the inset drawing. Tie the wire tie Make sure that the power cord is unpluggedDo not fully fold the Frame yet Not overtighten the Nut the Wheel must turn FreelyGers do not fully tighten the Bolts yet Careful not to pinch the Upright WireNot fully fold the Frame yet Your fingers do not fully tighten the Bolts yetPage Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Start the walking beltTurn on the fan if desired Measure your heart rate if desiredPress the Start button to start the workout HOW to USE a Classic WorkoutSelect a weight loss workout HOW to USE the Weight Loss WorkoutInformation Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Top Problem The walking belt slows when walked onProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description Part LIST-Model No. GGTL03607.2Key No. Qty Description Exploded Drawing A-Model No. GGTL03607.2 R0508A Exploded Drawing B-Model No. GGTL03607.2 R0508A Exploded Drawing C-Model No. GGTL03607.2 R0508A Exploded Drawing D-Model No. GGTL03607.2 R0508A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT