NordicTrack NTL07707.2 Be careful not to pinch the Upright Wire, Do not fully fold the Frame yet

Page 8

4. Set the Right Upright Spacer (79) on the Base

4

 

 

 

(83). Be careful not to pinch the Upright Wire

 

 

 

 

 

6

 

(38). With the help of a second person, insert

 

 

 

two 3/8” x 5” Bolts (6) with two 3/8" Star

 

 

 

77

Washers (9) into the Right Upright (78) and set

78

 

 

 

 

 

the Right Upright into the Right Upright Spacer.

 

 

 

79

9

 

If necessary, use a rubber mallet on top of the

 

 

 

 

Right Upright to make sure that the Upright is

 

 

 

 

fully inserted into Spacer.

 

 

 

 

Partially tighten the 3/8” x 5” Bolts (6) by turning

 

 

 

38

them several times; do not fully tighten the

 

 

 

 

 

 

 

Bolts yet.

 

 

 

 

Press a Base Endcap (77) into the Base (83).

83

 

 

 

 

 

 

 

5. With the help of a second person, carefully tip

5

 

 

 

the treadmill onto its right side. Partially fold the

 

 

 

 

 

 

 

Frame (56) so that the treadmill is more stable;

A

 

 

B

do not fully fold the Frame yet.

 

 

 

 

 

 

Remove and discard the two indicated bolts (A)

 

 

 

83

and the shipping bracket (B).

81

 

 

 

 

 

56

Attach a Base Pad (81) to the Base (83) in the

 

 

 

 

 

 

 

location shown with a #8 x 1" Tek Screw (2) and

2

 

 

113

a Base Pad Spacer (13). Then, attach another

 

 

 

 

 

 

 

Base Pad (81) with only a #8 x 1" Tek Screw (2).

 

 

13

 

 

 

 

 

Remove the 3/8" Nut (8), the 3/8" x 2" Shoulder

 

 

 

84

Bolt (113), and the shipping bracket (C) from the

 

 

 

Base (83). Attach a Wheel (84) with the Bolt and

 

 

2

81

the Nut that you just removed. Do not over-

 

 

C

 

 

 

tighten the Nut; the Wheel must turn freely.

 

 

 

8

Discard the shipping bracket.

 

 

 

 

6. Set the Left Upright Spacer (76) on the Base

6

 

 

 

(83). With the help of a second person, insert

 

 

 

77

 

 

 

two 3/8” x 5” Bolts (6) with two 3/8" Star

6

 

74

Washers (9) into the Left Upright (74) and set

 

 

 

 

 

 

 

the Left Upright into the Left Upright Spacer. If

 

9

 

76

necessary, use a rubber mallet on top of the Left

 

 

 

 

 

 

 

Upright to make sure that the Upright is fully in-

 

 

 

 

serted into the Left Upright Spacer.

 

 

 

 

Partially tighten the 3/8” x 5” Bolts (6) by turning

 

 

 

 

them several times; do not fully tighten the

 

 

 

 

Bolts yet.

 

 

 

 

Press a Base Endcap (77) into the Base (83).

 

 

 

83

 

 

 

 

With the help of a second person, tip the tread-

 

 

 

 

mill so that the Base (83) is flat on the floor.

 

 

 

 

 

8

 

 

 

Image 8
Contents QUESTIONS? Please do not ContactCall TOLL-FREE On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged See the inset drawing. Tie the long tieBe careful not to pinch the Upright Wire Them several times do not fully tighten Bolts yetDo not fully fold the Frame yet Tighten the Nut the Wheel must turn freelyTor and try again. if the Connectors are Sole MAY be Damaged When Power is Turned onPinch the wires Not Connected PROPERLY, the CONPage Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleChange the incline of the treadmill as desired Measure your heart rate if desired Turn on the fan if desiredHOW to USE a Preset Workout Select one of the preset workoutsHOW to USE AN Ifit Card Insert an iFIT card and select a workoutHOW to Adjust the Cushioning System HOW to USE the Stereo Sound SystemInformation Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR1107A Key No. Qty DescriptionQty Exploded Drawing A-Model No. NTL07707.2 Exploded Drawing B-Model No. NTL07707.2 Exploded Drawing C-Model No. NTL07707.2 Exploded Drawing D-Model No. NTL07707.2 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty