JVC MX-D402T manual Setting the Clock, Turning the Power On and Off, Adjusting the Volume

Page 10

Setting the Clock

1

2 , 4

3 , 5

Before operating the unit, set the correct time.

You can set the clock whether the Unit is on or off.

1. Press TIMER/CLOCK.

The hour digits begin flashing.

Flashing

2. Press 4 P. DOWN or ¢ P. UP on the MULTI CONTROL to set the hours.

Press ¢P. UP to increase the hour. Press 4 P. DOWN to decrease the hour. Holding down continuously changes the hour setting more rapidly.

3. Press SET.

The minute digits begin flashing.

Flashing

4. Press 4 P. DOWN or ¢ P. UP on

the MULTI CONTROL to set the minutes.

Press ¢P. UP to increase the minutes. Press 4 P. DOWN to decrease the minutes. Holding down continuously changes the minute setting more rapidly.

5. Press SET.

“CLOCK OK” appears on the display.

The clock stops flashing, and the clock timer starts from 0 second.

If the clock is not set, “AM 12:00” will flash instead of the clock indication.

When the time has been set, TIMER/CLOCK can be used to operate the Daily Timer and Recording Timer.

To adjust the time once the clock has been set, press CLOCK/TIMER 5 times and follow the proce- dure above.

CAUTION: If there is a power failure, the clock loses its setting. The display shows “AM12:00”, and the clock must be reset.

Turning the Power On and Off

Turning the System On ——————————————————

POWER

or

Press POWER. “WELCOME” appears on the display and the STANDBY indicator goes out.

The System comes on ready to continue in the mode it was in when the power was last turned off.

If the last thing you were doing was listening to a tape in Deck B, you are now ready to listen to a tape again in Deck B, or you can change to another source.

If you were listening to the Tuner last, the Tuner comes on playing the station it was last set to.

Turning the System Off ——————————————————

Press POWER again.

“GOOD BYE” appears on the display for a while and the STANDBY indicator lights up. The clock time appears on the display.

Some power (12 watts) is always consumed even though the power is on standby.

To switch off the Unit completely, unplug the AC power cord from the AC outlet. When you unplug the AC power cord, the clock will be reset to AM12:00 immediately, and preset Tuner stations will be erased in a few days.

+

or VOLUME

–

Adjusting the Volume

Turn VOLUME clockwise to increase the volume or anticlockwise to decrease it. Turning VOLUME quickly also adjusts the volume level quickly.

When using the Remote Control, press VOLUME + to increase the volume or press VOLUME – to decrease it.

You can adjust the volume level between 0 and 50.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents MX-D402T Important for Laser Products Power cord FeaturesInstallation of the Unit How This Manual Is OrganizedTable of Contents Using the Remote Control AccessoriesHow to Put Batteries in the Remote Control Getting StartedUsing the Supplied Wire Antenna Connecting the FM AntennaConnecting the AM Antenna Using an FM 75-Ohm Antenna Cable not suppliedVCR or other equipment Connecting the SpeakersConnecting Auxiliary Equipment Right SpeakerOn the Unit On the Remote ControlCompu Play buttons Common Operations Demo ModeDisplay Adjusting the Volume Setting the ClockTurning the Power On and Off Turning the System OnReinforcing the Bass Sound Sound ModesCustomizing a Sound Mode Changing the DisplayTurn down the volume level to Press AUX Listening to Auxiliary EquipmentSwitching between Frequency Bands Using the TunerTuning in a Station On the Unit Press FM/AMChanging the FM Reception Mode Presetting StationsThree Ways to Select a Station Disc indicator Using the CD PlayerEntering CD Operation Mode with the Remote Control CD indicatorLoading CDs Basics of Using the CD Player Continuous PlayPlaying a CD Fast Forward / Reverse Locating a Track with the Remote Control DirectlySelecting a Track Changing Discs While PlayingSelect a disc with Disc 1 to On the Remote Control Press PROGRAM/RANDOM on the UnitPrograming the Playing Order of the Tracks Track numberChanging the Program Random PlayChecking the Program Press the number keys 1 to 10 and +10 to select the tracksLocking the Trays Repeating a Track or the DiscsTray Lock Function Unlocking the TraysTape Direction Indicator on the Display Using the Cassette DeckEntering the Tape Operation Mode with the Remote Control Tape ª £Fast Left And Fast Right Regular PlayMusic Scan Finding the Beginning of the Current SelectionReverse Mode Reverse Mode on Reverse Mode OFFRecording Things to Know before You Start RecordingPress Tape Control then press Standard RecordingCheck the recording direction for the tape To pause at any time during the recording processAuto Edit Recording CD Direct RecordingRecording AM Station to Tape Press Dubbing How to Use DubbingTape to Tape Recording Dubbing To stop dubbing, press 7STOPUsing the Timer SleepSet the time you want the Unit to turn on Setting the Daily TimerPress TIMER/CLOCK again Set the time you want the Unit to turn offTo change the Daily Timer setting Turning the Daily Timer On and OffSetting the volume level To use a Cassette Deck as the sourceSetting the Recording Timer To change the Recording Timer setting Setting the Sleep TimerTurning the Recording Timer On and Off To change the Sleep Timer settingRecording Timer Timer PriorityExample Setting Operation Sleep TimerCare and Maintenance Possible Cause TroubleshootingSymptom ActionSpecifications HOW to Locate Your JVC Service Center Don’t service it yourselfLimited Warranty AUDIO-1 0398TNMNATJEM
Top Page Image Contents