JVC MX-D402T manual Standard Recording, Check the recording direction for the tape

Page 26

RECPAUSE

TAPE CONTROL

\

CAUTION: If recordings you have made have excessive noise or static, the Unit may be too close to a TV which was on during recording. Either turn off the TV or increase the distance between the TV and the System.

Standard Recording

This is the basic method for recording any source. The System also has special ways for recording CD to tape, and tape to tape, which save your time and effort, as well as give you some special effects. However, when you need to add a selection to a tape you have made, or are combining selections from several sources on one tape, use the method described below; just substitute the source you want into this procedure, such as a CD or the Tuner. You can also record from auxiliary source with this procedure.

Using the Unit

1.Insert a blank or erasable tape into Deck B.

2.Press REVERSE MODE if you want to record on both sides of the tape.

Reverse Mode comes on.

•When using Reverse Mode, insert the tape so that it will be recorded in the forward (3) direction.

3.Check the recording direction for the tape.

Check that the Tape Direction indicator is the same as that for the tape in the tape deck. If the directions are different, press 7STOP after pressing TAPE ª £ to set the tape direction.

•When using the Reverse Mode to record both sides of a tape, check that the Tape Direction indicator is in the forward (3) direction. If the direction indicator is not in the forward (3) direction, press TAPE ª £ then press 7STOP.

4.Prepare the source, for example, by tuning in a radio station, loading CDs, or turning on connected equipment.

5.Press REC START/STOP.

The REC indicator lights up and the System begins recording.

Using the Remote Control

1.Insert a blank or erasable tape into Deck B.

2.Press REVERSE MODE on the Unit if you want to record on both sides of the tape.

Reverse Mode comes on.

• When using Reverse Mode, insert the tape so that it will be recorded in the forward (3) direction.

3.Prepare the source, for example, by tuning in a radio station, loading CDs, or turning on connected equipment.

4.Press REC PAUSE.

The REC indicator starts flashing.

5.Press TAPE CONTROL then press 3.

Recording starts.

The REC indicator stops flashing and remains lit.

Notes for using Reverse Mode for recording

When recording with Reverse Mode on, the System automatically stops when it reaches the end of the reverse (2) direction. To record on both sides of a tape, make sure that the recording direction for the tape inserted into Deck B is forward (3), and that the Tape Direction indicator is also forward (3), before you start recording.

To pause at any time during the recording process

Press REC PAUSE on the Remote Control. Then press 3on the Remote Control or REC START/STOP on the Unit to restart recording.

To stop at any time during the recording process

Press REC START/STOP on the Unit again, or press 7 on the Remote Control.

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents MX-D402T Important for Laser Products Power cord FeaturesInstallation of the Unit How This Manual Is OrganizedTable of Contents Using the Remote Control AccessoriesHow to Put Batteries in the Remote Control Getting StartedUsing the Supplied Wire Antenna Connecting the FM AntennaConnecting the AM Antenna Using an FM 75-Ohm Antenna Cable not suppliedVCR or other equipment Connecting the SpeakersConnecting Auxiliary Equipment Right SpeakerCompu Play buttons On the Remote ControlOn the Unit Display Demo ModeCommon Operations Adjusting the Volume Setting the ClockTurning the Power On and Off Turning the System OnReinforcing the Bass Sound Sound ModesCustomizing a Sound Mode Changing the DisplayTurn down the volume level to Press AUX Listening to Auxiliary EquipmentSwitching between Frequency Bands Using the TunerTuning in a Station On the Unit Press FM/AMThree Ways to Select a Station Presetting StationsChanging the FM Reception Mode Disc indicator Using the CD PlayerEntering CD Operation Mode with the Remote Control CD indicatorPlaying a CD Basics of Using the CD Player Continuous PlayLoading CDs Fast Forward / Reverse Locating a Track with the Remote Control DirectlySelecting a Track Changing Discs While PlayingSelect a disc with Disc 1 to On the Remote Control Press PROGRAM/RANDOM on the UnitPrograming the Playing Order of the Tracks Track numberChanging the Program Random PlayChecking the Program Press the number keys 1 to 10 and +10 to select the tracksLocking the Trays Repeating a Track or the DiscsTray Lock Function Unlocking the TraysTape Direction Indicator on the Display Using the Cassette DeckEntering the Tape Operation Mode with the Remote Control Tape ª £Fast Left And Fast Right Regular PlayMusic Scan Finding the Beginning of the Current SelectionReverse Mode Reverse Mode on Reverse Mode OFFRecording Things to Know before You Start RecordingPress Tape Control then press Standard RecordingCheck the recording direction for the tape To pause at any time during the recording processRecording AM Station to Tape CD Direct RecordingAuto Edit Recording Press Dubbing How to Use DubbingTape to Tape Recording Dubbing To stop dubbing, press 7STOPUsing the Timer SleepSet the time you want the Unit to turn on Setting the Daily TimerPress TIMER/CLOCK again Set the time you want the Unit to turn offTo change the Daily Timer setting Turning the Daily Timer On and OffSetting the volume level To use a Cassette Deck as the sourceSetting the Recording Timer To change the Recording Timer setting Setting the Sleep TimerTurning the Recording Timer On and Off To change the Sleep Timer settingRecording Timer Timer PriorityExample Setting Operation Sleep TimerCare and Maintenance Possible Cause TroubleshootingSymptom ActionSpecifications HOW to Locate Your JVC Service Center Don’t service it yourselfLimited Warranty AUDIO-1 0398TNMNATJEM
Top Page Image Contents