JVC MX-D402T Presetting Stations, Changing the FM Reception Mode, Three Ways to Select a Station

Page 15

FMAM

or

On the Remote Control

To tune in FM stations, press FM.

To tune in AM stations, press AM.

COMPU PLAY

When FM or AM is pressed while the power is on standby, the power is automatically turned on.

Three Ways to Select a Station ——————————————

or

 

Press 1TUNING DOWN or TUNING UP Áon the MULTI CONTROL repeatedly to move

 

from frequency to frequency until you find the one you want. (Manual Tuning).

 

 

OR

 

 

Press and hold 1TUNING DOWN or TUNING UP Áon the MULTI CONTROL for a few

 

 

 

 

seconds, the frequency starts changing on the display. When a station is tuned in, the frequency stops

 

 

changing. (Auto Tuning).

 

 

OR

or

 

Possible only after presetting stations.

 

 

 

Press once and release 4P. DOWN or ¢P. UP on the MULTI CONTROL to go to the next

 

 

preset station.

 

 

You can also use the Remote Control to tune in preset channels:

1.Press FM or AM so that you can receive the last station tuned in.

2. Select the station by entering the preset number in the number keys of the Remote Control.

• Example: for channel 5, press 5. For channel 15, press +10 then 5.

For channel 20, press +10, then 10. For channel 30, press +10 twice then 10.

• After you have selected the preset number and the number appears, the broadcast frequency of the selected channel appears on the display.

Presetting Stations

1

2

You can preset up to 30 FM stations and up to 15 AM stations for the preset numbers.

Note: In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.

3 , 5

4

1.Select a band by pressing FM/AM on the Unit.

When using the Remote Control, press FM or AM.

or

2. Press 1 TUNING DOWN or TUNING UP Á on the MULTI

 

CONTROL to tune into a station.

3. Press SET.

“SET” flashes for 5 seconds.

While it is still flashing, carry out the following procedure.

4. Press 4 P. DOWN or ¢ P. UP on the MULTI

CONTROL on the Unit to set the preset number.

5. Press SET again.

“STORED” flashes for 2 seconds. The preset station is stored in the memory.

6. Repeat steps 1 to 5 for each station you want to store in memory using different preset numbers.

CAUTION: If the Unit is unplugged or if a power failure occurs, the preset stations will be erased in a few days. If this happens, preset the station again.

FM MODE

Changing the FM Reception Mode

When an FM stereo broadcast is hard to receive or noisy, press FM MODE on the Remote Control so that the MONO indicator lights up on the display. Reception improves, but there is no stereo effect.

To restore the stereo effect, press FM MODE on the Remote Control so that the MONO indicator goes out. In this stereo mode, the STEREO indicator lights up and you can hear stereo effects, when a program is broadcast in stereo.

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents MX-D402T Important for Laser Products How This Manual Is Organized FeaturesInstallation of the Unit Power cordTable of Contents Getting Started AccessoriesHow to Put Batteries in the Remote Control Using the Remote ControlUsing an FM 75-Ohm Antenna Cable not supplied Connecting the FM AntennaConnecting the AM Antenna Using the Supplied Wire AntennaRight Speaker Connecting the SpeakersConnecting Auxiliary Equipment VCR or other equipmentOn the Remote Control On the UnitCompu Play buttons Demo Mode Common OperationsDisplay Turning the System On Setting the ClockTurning the Power On and Off Adjusting the VolumeSound Modes Reinforcing the Bass SoundChanging the Display Customizing a Sound ModeListening to Auxiliary Equipment Turn down the volume level to Press AUXOn the Unit Press FM/AM Using the TunerTuning in a Station Switching between Frequency BandsPresetting Stations Changing the FM Reception ModeThree Ways to Select a Station CD indicator Using the CD PlayerEntering CD Operation Mode with the Remote Control Disc indicatorBasics of Using the CD Player Continuous Play Loading CDsPlaying a CD Changing Discs While Playing Locating a Track with the Remote Control DirectlySelecting a Track Fast Forward / ReverseTrack number On the Remote Control Press PROGRAM/RANDOM on the UnitPrograming the Playing Order of the Tracks Select a disc with Disc 1 toPress the number keys 1 to 10 and +10 to select the tracks Random PlayChecking the Program Changing the ProgramUnlocking the Trays Repeating a Track or the DiscsTray Lock Function Locking the TraysTape ª £ Using the Cassette DeckEntering the Tape Operation Mode with the Remote Control Tape Direction Indicator on the DisplayFinding the Beginning of the Current Selection Regular PlayMusic Scan Fast Left And Fast RightReverse Mode on Reverse Mode OFF Reverse ModeThings to Know before You Start Recording RecordingTo pause at any time during the recording process Standard RecordingCheck the recording direction for the tape Press Tape Control then pressCD Direct Recording Auto Edit RecordingRecording AM Station to Tape To stop dubbing, press 7STOP How to Use DubbingTape to Tape Recording Dubbing Press DubbingSleep Using the TimerSet the time you want the Unit to turn off Setting the Daily TimerPress TIMER/CLOCK again Set the time you want the Unit to turn onTo use a Cassette Deck as the source Turning the Daily Timer On and OffSetting the volume level To change the Daily Timer settingSetting the Recording Timer To change the Sleep Timer setting Setting the Sleep TimerTurning the Recording Timer On and Off To change the Recording Timer settingSleep Timer Timer PriorityExample Setting Operation Recording TimerCare and Maintenance Action TroubleshootingSymptom Possible CauseSpecifications Don’t service it yourself HOW to Locate Your JVC Service CenterLimited Warranty AUDIO-1 0398TNMNATJEM
Top Page Image Contents