Image IMBE53991 user manual Tighten all of the Nylon Locknuts used in steps 1 to

Page 10

12.Place the Right Safety Spotter (23) on the right Base

(7) and center it over the indicated hole. Note: The handle must point toward the center of the bench.

Have a second person hold the Locking Bar (34) so that the Right Weight Glider (31) rests on top of the Right Safety Spotter (23). Insert a Weight Guide (18) into the Right Weight Glider, the Right Safety Spotter, and the hole in the Base (7). Note: Tilt the Weight

Guide away from the Upright (1) as you insert it.

Attach the Weight Guide (18) to the Base (7) with an M8 x 60mm Bolt (39), two M8 Washers (52), and an M8 Nylon Locknut (54). Do not tighten the Nylon

Locknut yet.

13.Note: If you are not planning to use Olympic weights with the weight bench, you do not need to perform this step. Keep the two Weight Adapters (33) in a safe place in case you need them in the future.

Fully engage the indicated hook on both sides of the weight bench before beginning this step.

Insert a 50mm Bushing (47) into the end of a Weight Adapter (33). With a second person holding the Barbell (35) so that it cannot turn, use the allen wrench to secure the Weight Adapter to the Barbell with a Large Washer (44) and an M10 x 25mm Button Head Bolt (43). Note: The Large Washer must fit into the indentation in the 50mm Bushing in the Weight Adapter.

Pull the remaining length of the Barbell (35) in the direction shown. Next, tighten the M8 x 20mm Screws used in steps 9 and 10. Attach the other Weight Adapter (33) to the other end of the Barbell

(35)in the same manner.

14.Attach the upper end of one of the Weight Guides

(18)to the bracket on the Upright (1) with an M8 x 30mm Bolt (38) and an M8 Washer (52).

Attach the other Weight Guide (18) to the other Upright (1) in the same manner.

Tighten all of the Nylon Locknuts used in steps 1 to 14.

12

 

 

18

 

 

 

1

 

31

 

 

Handle

7

 

 

 

23

 

 

39

 

 

52

Hole

34

 

54

 

13

 

 

Hook

 

 

35

 

 

 

33

 

 

 

47

 

 

44

 

 

43

14

 

 

 

38

 

 

52

 

18

1

 

 

 

10

Image 10
Contents Model No. IMBE53991 Serial No Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Right Side Before You BeginLeft Side Part Identification Chart-Model No. IMBE53991 R1200A Assembly Nylon Locknuts yet En the Nylon Locknuts yet Each Bolt. Do not tighten the Nylon Locknuts yetTighten the Nylon Locknuts yet Guide away from the Upright 1 as you insert it Locknut yetTighten all of the Nylon Locknuts used in steps 1 to Lubricate Holes Welded Tube Nylon Locknut the Seat Adjustment Bracket must pivot easily LocknutLocknut the Seat Support Tube must pivot easily Adjusting the Weight Bench Using the Locking BAR and Safety SpottersAdjusting the Backrest Part List-Model No. IMBE53991 Qty DescriptionExploded Drawing Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT