Healthrider HRSY54370 manual

Page 9

11.Press a 1Ó Round Inner Cap (36) into one of the Press Arms (6). Press a 1 3/4Ó Square Inner Cap

(65)into the Press Arm.

Repeat this step for the other Press Arm (6).

12.Identify the Right Butterfly Arm (15) and the Left Butterfly Arm (14). Note the position of the welded bracket on each Arm. Butterfly Arm identification is very important for step 13.

Attach a Pulley (41) and a Cable Trap (67) to the Right Butterfly Arm (15) with a 3/8Ó x 2Ó Bolt (43) and a 3/8Ó Nylon Locknut (39) but do not fully tighten the Nylon Locknuts yet.

Attach a Pulley (41) and a Cable Trap (67) to the Left Butterfly Arm (14) with a 3/8Ó x 2Ó Bolt (43) and a 3/8Ó Nylon Locknut (39) but do not fully tighten the Nylon Locknuts yet.

Press 1 3/4Ó Square Inner Caps (65) into the ends of the Right and Left Butterfly Arms (15, 14). Wet the lower end of each Arm with soapy water. Slide a Butterfly Foam Pad (23) onto the lower end of each Arm.

13.Lubricate the axle on the Right Butterfly Arm (15) .

Slide the axle on the Right Butterfly Arm (15) into the Frame (2). Note: Be careful not to confuse the Right Butterfly Arm with the Left Butterfly Arm (14); refer to step 12 to identify the Right Butterfly Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the Frame (2).

IMPORTANT NOTE: Before assembling the 3/4Ó Retainers (70) be sure that you thoroughly understand the step. The Retainers can be assembled only once. If they must be removed, you will need to order new Retainers.

Slide a 3/4Ó Large Washer (71) onto the axle on the Right Butterfly Arm (15). Tap two 3/4Ó Retainers (70) and a 3/4Ó Round Cover Cap (69) onto the axle. Be sure that the teeth on the

Retainers bend toward the Cover Cap, as shown in the inset drawing.

Attach the Left Butterfly Arm (14) in the same manner.

9

11

65

 

 

 

 

 

 

36

 

 

 

 

 

65

 

6

 

 

 

 

 

36

 

 

 

6

12

 

 

39

 

 

 

 

 

65

 

 

15

41

 

 

 

 

 

 

67

14

 

 

 

 

24

43

 

 

 

 

 

65

 

24

 

 

 

 

 

65

 

13

 

 

 

 

 

69

 

 

70

 

 

 

71

 

 

 

Bracket

 

70

 

 

71

 

15

 

 

 

 

 

 

 

2

 

Lubricate

 

 

 

Axles

 

14

 

 

 

 

 

 

69

 

 

 

70

 

 

 

71

 

 

 

Axle

Image 9
Contents QUESTIONS? Model No. HRSY54370 Serial NoCustomer HOT Line Limited Warranty Table of ContentsImportant Precautions Before YOU Begin Assembly Chart located in the center of this manualFollowing Tools not Included are Required for Assembly Page Tighten the Nylon Locknuts used in steps 3Ð5 now Do not tighten the Nylon Locknuts yetTighten the Nylon Locknuts from now Page Page Page Changing the Resistance Setting AdjustmentAttaching the LEG Lever to the LOW Pulley Station Seat AdjustmentTightening the Cable TROUBLE-SHOOTING and MaintenanceCable Diagram Page Page Qty Description Part LISTÑModel No. HRSY54370Exploded Ordering Replacement Parts