Gold's Gym GGBE25580 manual See . Tighten the M6 x 47mm Screws Holes Grease Tube

Page 9

7.Attach the Medium Pin (45) to the Seat Frame (11) with an M4 x 16mm Screw (58).

Attach the Seat (14) to the Seat Frame (11) with two M6 x 16mm Screws (61), two M6 x 35mm Screws (56) and two M6 Washers (68).

8.Orient the Backrest Frames (12) so that the indi- cated holes are closer to the tops of the Frames.

Apply some of the included grease to an M10 x 185mm Hex Bolt (63). Attach the Backrest Support (13) between the Backrest Frames (12) with the Hex Bolt and an M10 Nylon Locknut (66).

Do not overtighten the Nylon Locknut; the Backrest Support must pivot easily.

Next, attach the Backrest (29) and the Headrest (23) to the Backrest Frames (12) with six M6 x 55mm Screws (67) and six M6 Washers (68). Do not tighten the Screws yet.

9.Note: For clarity, the seat is not shown in this step.

Grease an M10 x 185mm Hex Bolt (63). Attach the Seat Frame (11) and the Backrest Frames (12) to the Seat Carriage (22) with the Hex Bolt and an M10 Nylon Locknut (66). Do not overtighten the Nylon Locknut; the Seat Frame and the Backrest Frames must pivot easily.

Insert the Medium Pin (45) through a hole in the Seat Frame (11) and the tube on the Seat Carriage (22).

See the inset drawing. Grease an M10 x 80mm Hex Bolt (24). Attach the Backrest Support (13) to the Bench Frame (3) with the Hex Bolt and an M10 Nylon Locknut (66). Do not overtighten the

Nylon Locknut; the Backrest Support must pivot easily.

See step 8. Tighten the M6 x 47mm Screws (67).

9

7

 

 

 

14

 

58

 

 

 

 

11

 

45

68

 

 

 

61

56

8

 

23

 

 

 

29

 

 

 

12

66

Holes

 

 

68

 

 

68

 

67

 

 

 

 

63—Grease

 

67

13

 

 

9

 

 

45

66

12

11

 

 

 

 

Grease

 

22

63

 

 

 

Tube

 

 

 

66

 

 

13

 

 

Grease

 

 

24

 

 

3

Image 9
Contents QUESTIONS? Model No. GGBE2558.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Before YOU Begin Right SideLeft Side Part Identification Chart Make Assembly Easier AssemblyPage Tighten the M10 Nylon Locknuts 66 used in steps See . Tighten the M6 x 47mm Screws Holes Grease Tube Grease Page Adjustment Adjusting the BackrestAdjusting the Seat Using Your Weights Attaching the Curl PADAttaching the Curl BAR Adjusting the Safety Spotters Exercise Guidelines Muscle Chart Cooling DownStaying Motivated Qty Description Part LIST-Model No. GGBE2558.0Exploded Drawing A-Model No. GGBE2558.0 Exploded Drawing B-Model No. GGBE2558.0 R0308A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT