Coleman 2000002596 manual To Set Up Tent, Hinged, Rigid Door

STITCH LINE

	ROCKWALLTM	12 TENT MODEL 2000002596
Before you begin			Curved Ridge Pole		Curved Ridge Pole in		Curved Ridge Pole	Fig. 6
Read all instructions before set up.			in sleeve		sleeve with Red Marking		in sleeve
• Select a level site clear of rocks, branches, and other hard or sharp
	objects, to install your tent.
	WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential lightning strikes
	or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage						Door
	or personal injury.
•	For best results in windy conditions, position narrow end of tent into
	the wind.		Short Leg Pole	Long Leg Pole		Front of Tent		Short Leg Pole
•	Enlist the help of at least one other person to assist you when it is time		8. Rotate all six Leg Poles upright and insert pin on each web
	to assemble the tent.
			loop at the side locations as shown. (Fig. 7 & 7A)

Pole Descriptions

Fig. 7

Pole

Pole

Pole

Description

Qty.

Dia.

Repair Kit

Replacement Kit

Long Leg Pole, steel

(w/ red marking)

2

19mm

N/A

5010000678

Short Leg Pole, steel

4

19mm

N/A

5010000680

Curved Ridge Pole, steel

(w/ red marking)

1

19mm

N/A

5010000677

Curved Ridge Pole, steel

2

19mm

N/A

5010000679

7A

Vertical Door Pole, black,

short w/rubber tips

1

6.3mm

5010000543

5010000545

Door Pole, black,

long w/rubber tips

1

6.3mm

5010000543

5010000545

Pin

Self-Rolling Window Spring Descriptions

9. Stretch tent to finished size:

Color Code Description

Qty.

Length

Replacement Part No.

•

Push in button on Leg Pole while

Fig. 8

twisting lower Leg Pole section

Green

1

610mm

5010000627

counterclockwise (Fig. 8);

Upper

Orange

10

670mm

5010000628

•

Pull up on top Leg Pole section until

Leg Pole

tent is taut;

CAUTION: “Springs” may have sharp edges. Handle with care to avoid

Section

•

Twist the lower Leg Pole clockwise

injury. Keep out of reach of children.

until the button locks into the center

Button

or lowest hole;

Center Hole

To Set Up Tent

•

Repeat on remaining Leg Poles.

Lower Hole

1.

Unfold tent and spread out on a clean, level surface with the door

10. Locate Frame Clips on front and back of

Lower

tent; then attach to Leg Poles as shown.

facing the desired direction.

Leg Pole

(Fig. 9)

Section

11. Insert plastic stakes through

Fig. 1

Curved Ridge Poles (3)

web straps located at bottom

of each Leg Poles; then drive

Leg Poles,

in to secure. (Fig. 10)

short (4)

Leg Poles,

long (2)

2.

Assemble six, steel, shock-corded, Leg Poles.

Fig. 9

Fig. 10

(Fig. 1)

3. Push down on steel button on tapered end

Hinged, Rigid Door

and insert into end with four holes.

Button in

1.

Assemble Vertical Door Pole (shorter black pole with plastic tips);

NOTE: Make sure steel button locks into

third hole

Fig. 2

then insert through zippered vertical pole sleeve on hinged side of

third hole on pole as shown. (Fig. 2)

4.

Assemble three, steel, shock-corded, curved

door. (Fig. 11)

Ridge Poles. (Fig. 1)

2. Insert end of Vertical Door Pole into bottom hinge plate, apply

5. Stretch four corners of tent until taut; then

pressure to form a slight bow, then insert other tip of pole into top

drive plastic stake web strap of each to

hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)

secure. (Fig. 3)

3. Assemble Door Pole (longer black pole with plastic cap tips); then

insert into zippered pole sleeve at top of door. (Fig. 14)

Fig. 3

4. Insert end of Door Pole into top hinge plate, apply pressure to form

a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)

6.

Insert Ridge Pole (with red marking) into center sleeve on top of tent

5.

Zip up pole sleeve to enclose Door Pole. (Fig. 16)

with the red trim (Fig. 4 & 6). Insert the remaining curved Ridge Poles

Fig. 11

Fig. 12

Fig. 13

into the other two sleeves on top of tent.

7.

Vertical Pole

Insert curved end of Leg Pole (with red marking) into the ends of the

Sleeve

Ridge Pole (with red dot). Insert curved end of remaining short Leg

Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6)

Fig. 4			Door Hinge
	Ridge Pole with
	Red Marking
Curved				Fig. 14	Fig. 15
Ridge Pole	Curved End of
with Red
Marking	Long Leg Pole	Sleeve	Top
		with Red
		Trim	Door	Pole
Sleeve			Hinge		Fig. 16
				Sleeve
with Red		Fig. 5
Trim					(continued on other side)