Life Fitness Models 9500HR / 9100 Exercise Bikes
Fitness Entertainment Kit Installation (Continued)
Step 11
Run the FITNESS ENTERTAINMENT CABLE ASSEMBLY down the front of the user left shroud making certain the FITNESS ENTERTAINMENT CABLE ASSEMBLY lays flat against the shroud. Insert the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the bottom CABLE CLAMP.
Step 12
Place a third CABLE CLAMP on the underside of the user left shroud front as close to the frame as possible (approximately 1” from the frame). Pull the excess FITNESS ENTERTAINMENT CABLE ASSEMBLY back into the bike until the FITNESS ENTERTAINMENT CABLE ASSEMBLY is tight against the user left shroud. Insert the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the third cable clamp.
Step 13
Bundle the excess FITNESS ENTERTAINMENT CABLE ASSEMBLY as shown in Figure 1 and secure with a supplied wire tie. Secure the bundled FITNESS ENTERTAINMENT CABLE ASSEMBLY to the frame away from moving parts as shown with another supplied cable tie.
Step 14
Apply two CABLE CLAMPS to the front of the user left shroud
Step 15
Reverse steps 1 through 3 to return all shroud parts to their proper positions. Tighten screws to 12 - 15 in. lbs.
Step 16
Model 9500HR: Apply a CABLE CLAMP approximately 3” down from the bend in the user left NECK SHROUD and approximately 1/4” from the NECK SHROUD OVERLAP JOINT. Position the CLAMP with the opening facing the NECK SHROUD OVERLAP JOINT. Continue routing the FITNESS ENTERTAINMENT CABLE ASSEMBLY upwards flat against the shroud and insert the FITNESS
Display ENTERTAINMENT CABLE ASSEMBLY into the CABLE CLAMP.
Console
Model 9100: Apply a CABLE CLAMP approximately 1/2 way up the handlebar vertical tube. Continue routing the FITNESS ENTERTAINMENT CABLE ASSEMBLY upwards flat against the handlebar vertical tube and insert the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the CABLE CLAMP.
Receiver
Step 17 (Cardio Theater Wireless System Only)
|
|
|
|
| NOTE: WITH A SUPPLIED ALCOHOL WIPE, CLEAN THE SHROUD AT EACH | |||||
|
|
|
|
| HOOK AND LOOP FASTENING STRIP LOCATION BEFORE MOUNTING THE | |||||
|
|
|
|
|
| HOOK AND LOOP FASTENING STRIPS. | ||||
|
|
|
| Cable | Remove the four screws and mounting block from the back of the FITNESS | |||||
|
|
|
| |||||||
|
|
|
| Clamp | ENTERTAINMENT RECEIVER. Remove the backing on one side of the hook and | |||||
|
|
|
| User Left | loop fastening strips provided and apply lengthwise to the back of the FITNESS | |||||
|
|
|
| Neck Shroud | ENTERTAINMENT RECEIVER. Remove the backing of the remaining side of the | |||||
|
| Cable Assembly | hook and loop fastening strips and apply the FITNESS ENTERTAINMENT | |||||||
|
| RECEIVER to the underside of the DISPLAY CONSOLE as shown. Press firmly to | ||||||||
|
|
|
|
| ||||||
|
|
|
|
| ensure proper adhesion. | |||||
Step 18 (Cardio Theater Wireless System Only) |
|
|
|
|
| Touch Pad | ||||
|
|
|
|
| ||||||
|
|
|
|
|
| |||||
Plug the FITNESS ENTERTAINMENT CABLE ASSEMBLY and the |
|
|
|
|
| |||||
FITNESS ENTERTAINMENT TOUCHPAD CABLE ASSEMBLY into |
|
|
|
|
| |||||
the appropriate jacks on the FITNESS ENTERTAINMENT |
|
|
|
|
| |||||
RECEIVER. |
| Handlebar |
|
| ||||||
|
| |||||||||
Step 19 |
|
|
|
|
|
| ||||
Using two supplied wire ties, mount the FITNESS |
|
|
|
|
|
| ||||
ENTERTAINMENT TOUCH PAD to the bike. Controller location is at | Display |
|
| |||||||
| ||||||||||
the discretion of the customer. Refer to the CARDIO THEATER or | Console | |||||||||
BROADCAST VISION MANUAL for suggested locations. |
|
|
|
|
| |||||
Model 9500HR: Do not install the FITNESS ENTERTAINMENT TOUCH PAD over the Lifepulse® electrodes.
Step 20
Receiver
Touch Pad Cable
Plug the remaining end of the FITNESS ENTERTAINMENT TOUCHPAD CABLE ASSEMBLY into the FITNESS ENTERTAINMENT TOUCHPAD (Cardio Theater Wireless System). Plug the end of the FITNESS ENTERTAINMENT CABLE ASSEMBLY into the
FITNESS ENTERTAINMENT TOUCHPAD.