Spirit XE 850 owner manual Foot PAD/CONNECTING ARM ASSEMBLY. Rear shroud installation

Page 13

STEP 4: FOOT PAD/CONNECTING ARM ASSEMBLY. Rear shroud installation.

1.Remove the hardware from the hardware pack for step 4. You should have two 5/16￿ x

1-1/4￿ bolts (79), two flat washers (100), two nylon nuts (91), four 5/16￿ x 3/4￿ bolts (80), two self-tapping Phillips head screws (107) and twenty-six M5 x 12mm screws (84).

2.On the pedal arms, in the middle on top, there are two axles (23) already installed in the bushing housings. Remove the bolt and washer (74, 99) from each then remove the axles and set them aside for the next steps.

3.Locate the left foot pad/connecting arm. Holding the rear of the footpad with your right hand, and the connecting arm with your left hand (just in front of the foot pad), place the footpad bracket over the bushing housing.

4.Holding the axle (removed in step 2) in one hand and the foot pad in the other line up the large hole in the side of the bracket (under the foot pad) with the hole in the bushing housing and insert the axle all the way until the head of the axle is flush against the bracket. You may have to wiggle the axle while moving the footpad slightly to get the axle to go in. Install and tighten the bolt and washer (74, 99) removed in step two.

5.Align the hole in the end of the connecting arm (pivoting rod end) with the hole in the bracket of the handle bar. The rod end should be on the inside of the handle bar bracket. Take one of the 5/16￿ x 1-1/4￿ bolts (79) and install it through the handle bar bracket and the rod end. Install a flat washer (100) and nylon nut (91) on the bolt and tighten firmly using a wrench on the nut and one on the bolt.

6.Repeat steps 3 ￿ 5 for the right side foot pad/connecting arm.

7.Install the plastic covers (71, 72) over the connection of the rod end and handle bar. The front inside hole in the plastic uses a self-tapping screw (DO NOT OVERTIGHTEN THIS SCREW) and the two rear holes use the M5 x 12mm screws (84). There is a short Phillips screwdriver provided for installing the inside screws.

8.Install the two wheel covers (64) using four M5 X 12mm screws (84).

9.Install the two middle stabilizer covers (116, 117) using two M5 x 12mm screws (84).

10.Rear shroud (steel cover) installation. Unpack the rear shrouds and remove the 12 screws (84) holding the four front caps (152, 153) to the left and right shrouds (150, 151).

11.Locate and install the four L shaped brackets (149) on the rear stabilizer tube using eight M5 x 12mm screws (84).

12.Locate and install the two middle mounting brackets (148). These two brackets install from beneath the left and right aluminium rails and are held in place by 5/16￿ x 3/4￿ bolts (80). There are holes in the center of the aluminium rails where the hole in the brackets line up and the bolts go through.

13.Install the shrouds by lifting the pedal arm and carefully sliding the shroud over the covered wheels of the pedal arms. Lower the pedal arms until the wheels are resting on the aluminium rails again. Position the shroud so the holes in the mounting brackets (148, 149) line up with the mounting holes in the shroud. Install and tighten the eight M5 x 12mm screws (84) that hold the shrouds in place.

14.Locate the two front retaining brackets (24) and install them from beneath the rails, just in front of the aluminium rail. These retaining brackets should line up with the brackets (147) that are pre-installed in the front of the shrouds. Line up the holes in the brackets and install the 5/16￿ x 3/4￿ bolts (80) from the top. It is easiest for installation if the pedal arm is rotated so it is at the top of the stroke, giving you freer access to these bolts.

15.Re-install the four front caps (152, 153) that were removed in step 10.

12

XE Series Elliptical

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Elliptical Table of Contents Product Registration Important Safety Instructions Important Operation Instructions Important Electrical InformationStep Assembly Pack Check List#102 Ø 25 Wave Washer 2 pcs Tools Unpacking the Unit Assembly InstructionsConsole Mast Assembly XE Series Elliptical Handle BAR Assembly Foot PAD/CONNECTING ARM ASSEMBLY. Rear shroud installation 107 152 153 150 151 Footpads FeaturesTransportation Operation of Your Elliptical XE850 Console Power onBasic information Quick StartProgramming the console Entering/Changing SettingsManual Preset ProgramsFat Burn ProgramsCardio Strength Custom User Defined Programs IntervalXE Series Elliptical Heart Rate programs Rate of Perceived Exertion Erratic Operation Using a Heart Rate TransmitterHeart Rate Control Program 1 & 2 HR 1, HR 2 operation Elliptical Warranty Manufacturer’s Limited Warranty

XE 850 specifications

The Spirit XE 850 is a state-of-the-art elliptical trainer designed for both commercial gyms and home fitness enthusiasts. It combines an array of innovative technologies and thoughtful design features to enhance the workout experience, making it one of the standout models in the Spirit Fitness lineup.

One of the notable features of the Spirit XE 850 is its robust construction. Built with heavy-duty materials, the frame provides stability and durability, accommodating users of all sizes and fitness levels. The machine boasts a weight capacity of up to 350 pounds, allowing for a wide range of users and ensuring a solid workout environment.

The XE 850 features a large, user-friendly console that displays essential workout metrics such as time, distance, calories burned, heart rate, and resistance level. The high-resolution LCD screen is easy to read from various angles, making it convenient for users during their workout. Additionally, the console includes built-in speakers and Bluetooth compatibility, allowing users to enjoy their favorite music or audio while they exercise.

One of the standout technologies of the Spirit XE 850 is its adjustable stride length. Users can customize the stride to accommodate different body types and workout preferences, which not only boosts comfort but also targets various muscle groups. The elliptical machine is equipped with 20 levels of resistance, providing ample opportunity for users to tailor the intensity of their workouts, whether they're beginners looking to build stamina or seasoned athletes seeking a challenging session.

Another important characteristic of the XE 850 is its ergonomic design. The multi-grip handlebar allows for different hand positions, which helps to engage more muscle groups while ensuring a comfortable grip. The adjustable foot pedals are designed with a slight inward angle, mimicking a natural walking or running motion and minimizing strain on the joints.

For those focused on heart rate training, the Spirit XE 850 includes contact heart rate sensors built into the handlebars, along with the option for wireless heart rate monitoring with compatible chest straps. This feature enables users to stay within their target heart rate zones, optimizing their workout efficiency.

In conclusion, the Spirit XE 850 stands out in the crowded market of elliptical trainers. Combining durability, versatility, and advanced technology, it offers a comprehensive workout solution for users at all fitness levels. Whether for casual users or dedicated athletes, the XE 850 helps create an enjoyable and effective exercise experience.
Top Page Image Contents