JVC RX-D201S manual Getting started, Before Installation, Putting batteries in the remote control

Page 6

Getting started

Before Installation

General precautions

Be sure your hands are dry.

Turn the power off to all components.

Read the manuals supplied with the components you are going to connect.

Locations

Install the receiver in a location that is level and protected from moisture and dust.

The temperature around the receiver must be between –5˚C and 35˚C (23˚F and 95˚F).

Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Leave sufficient distance between the receiver and the TV.

Handling the receiver

Do not insert any metal object into the receiver.

Do not disassemble the receiver or remove screws, covers, or cabinet.

Do not expose the receiver to rain or moisture.

Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

When you are away on travel or otherwise for an extended period or time, remove the plug from the wall outlet. A small amount of power is always consumed while the power cord is connected to the wall outlet.

The receiver has a built-in cooling fan which operates while the receiver is turned on. Be sure to leave enough ventilation to obtain sufficient cooling effect.

CAUTION:

Do not connect the AC power plug to the wall outlet until all

connections are completed.

Putting batteries in the remote control

Before using the remote control, put two supplied batteries first.

1

2

3

1Press and slide the battery cover on the back of the remote control.

2Insert batteries.

Make sure to match the polarity: (+) to (+) and (–) to (–).

3Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6(SUM-3)/AA(15F) type dry-cell batteries.

Supplied butteries are for initial setup. Replace for continued use.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

Use the correct type of batteries. Batteries that look similar may differ in voltage.

Always replace both batteries at the same time.

Do not expose batteries to heat or flame.

When using the remote control, aim the remote control directly at the remote sensor on the front panel.

Remote sensor

Checking the supplied accessories

Check to be sure you have all of the following supplied accessories. If anything is missing, contact your dealer immediately.

Remote control (1)

Batteries (2)

AM loop antenna (1)

FM antenna (1)

4

Image 6
Contents RX-D201S / RX-D202B For Customer UseFor Canada/pour le Canada For Canada/pour Le CanadaFor the main unit For U.S.ATable of Contents Remote control When operating a DVD player, set the mode selector 1 to DVDParts identification Display window Rear panelFront panel Checking the supplied accessories Before InstallationPutting batteries in the remote control Getting startedFM antenna supplied Connecting the FM and AM antennasFM antenna connection AntennaConnecting the speakers Connecting the speakersSpeaker Layout Diagram Connecting the powered subwooferWhite Connecting video componentsTurn off all components before making connections Only for DVD recorder To S-video inputGreen Component video cable not supplied Blue Red Not supplied White Composite videoVideo cable not supplied Composite video cable not supplied Connecting a DBS tuner Green Connecting a TVBlue Red USB Connection How to install the USB driversConnect the unit to the PC using a USB cable not supplied Digital connectionCheck if the drivers are correctly installed Connecting the power cordUSB drivers are installed automatically Now PC is ready for playback through the USB connectionTo turn off the power into standby Turn on the powerSelecting the analog or digital input mode Basic operationsInitial setting Dgtl Auto Adjust the volumeListening with headphones Ex. When Dolby Digital is selectedSignal and speaker indicators on the display Turning off the power with the Sleep TimerBasic adjustment of auto memory Turning off the sounds temporarilyPress SET Basic settingsPress Setting Before you start, rememberBasic setting items Speakers channels number and the sizeRoom size and the speaker distance/output level Setting the surround back speakers-S Back OUT Setting the speakersSetting subwoofer information-SUBWOOFER Turn Multi JOG to select the appropriate SettingFrom the remote control Activating the EX/ES/PLIIx setting- EX/ES/PLIIxSetting the speaker distance AutoSetting bass sound Using the Midnight modeSelecting the main or sub channel DVD S/C VCR S/CSound adjustments Basic adjustment itemsOperating procedure Press Sound Press Test again to stop the test toneAdjusting the virtual room size for DSP modes Adjusting the bass soundsAttenuating the input signal-INPUT ATT Adjusting the liveness effect for DSP modesAdjusting the center tone-CENTER Tone To store the preset stations Tuning in to stations manuallyUsing preset tuning Tuner operationsSelecting the FM reception mode To tune in a preset stationIntroducing the Surround modes Creating realistic sound fieldsReproducing theater ambience Dolby Digital3D Headphone mode About other digital signalsDTS All Channel Stereo mode ALL CH Stereo Introducing the DSP modesDigital Acoustic Processor DAP modes About the DSP modes Using the Surround/DSP modesDTSDolby Digital Incoming Signal Type Virtual Surround BackWhen you select Auto Surround Selecting the Surround/DSP modesConnections 2 Video cable connection AV Compu Link remote control systemConnections 1 AV Compu Link connection Monaural mini-plugs not suppliedAutomatic power on/off Connecting procedureAutomatic selection of TV’s input mode One-touch video playOperating other JVC products Changing the remote control code for DVD recorder DVD recorder or DVD playerRelease STANDBY/ON DVR/DVD Release STANDBY/ON TV/DBS/CATV Changing the transmittable signals for operating a TVOperating other manufacturers’ products Manufacturers’ codes for TVTry to operate your VCR by pressing Changing the transmittable signals for operating a VCRRelease STANDBY/ON VCR Manufacturers’ codes for VCRManufacturers’ codes for Catv converter/ DBS tuner Try to operate your DVD player by pressingManufacturers’ codes for DVD player Problem Possible Cause Solution TroubleshootingPower Remote control TunerFM tuner IHF SpecificationsAmplifier AM tunerPage Page Audio Video Control Receiver Page Page Page Page Page Page

RX-D202B, RX-D201S specifications

The JVC RX-D201S and RX-D202B are two high-performance stereo receivers that cater to the needs of audiophiles and casual listeners alike. These models are designed to deliver an immersive audio experience with a range of features and technologies that enhance sound quality and usability.

One of the standout features of the JVC RX-D201S and RX-D202B is their impressive power output. Both models deliver solid amplification, ensuring that even the most demanding speakers perform beautifully. The receivers offer a dynamic range that captures the nuances of your favorite music, whether you are listening to classical, rock, or electronic genres. With RMS power ratings that provide ample headroom, these receivers can fill a room with rich, detailed sound.

Connectivity is another key aspect of the RX-D201S and RX-D202B. The receivers come equipped with multiple input options, including HDMI, coaxial, optical digital inputs, and analog inputs, allowing users to connect a wide variety of audio and video devices, from Blu-ray players to gaming consoles. The inclusion of Bluetooth technology is a major advantage, enabling wireless streaming from smartphones and tablets. This feature provides added convenience for users who prefer to listen to music without the hassle of wired connections.

The receivers boast a user-friendly interface, making it easy for individuals of all technical backgrounds to navigate through settings and sources. The backlit remote control enhances usability, allowing users to manage their audio experience from across the room.

In terms of audio performance, both models are equipped with advanced sound processing technologies. They support various sound modes, allowing users to tailor the listening experience to their personal preferences. Features such as tone control and equalizer settings further enhance the versatility of the sound output.

The design of the JVC RX-D201S and RX-D202B is sleek and modern, with a minimalist aesthetic that fits well in any home entertainment setup. The built-in cooling system ensures consistent performance even during extended listening sessions, safeguarding the longevity of the unit.

In summary, the JVC RX-D201S and RX-D202B are superb choices for anyone seeking powerful, flexible, and user-friendly stereo receivers. With their robust features, impressive connectivity, and excellent audio quality, they stand out as reliable options in the competitive audio market. Users will find that these receivers excel in delivering a sophisticated listening experience that meets diverse musical tastes and preferences.