JVC CATD77 Playing the Source Using Dolby Pro Logic Mode, Getting Ready to Use Dolby Pro Logic

Page 21

Playing the Source Using Dolby Pro Logic Mode

Preparing the Dolby Pro Logic Reproduction ———————

For connecting the diagram, See page 6 ‘‘For Dolby Pro Logic Reproduction’’.

To use the Dolby Pro Logic mode, you need to prepare the various settings as follows:

Center Speaker Mode

Center Speaker mode contains the following four settings.

PHANTOM: Select this setting if you have not connected a center speaker. The left and right front speakers project the sound to give the effect of a center speaker.

NORMAL: Select this setting if you are using a small center speaker. Since the center speaker cannot boost the low tones effectively, this setting uses the front speakers to boost the low tones from the center speaker.

WIDE: Select this setting if you are using a center speaker that is similar in power to the front speakers.

OFF: Select this setting to turn off the output for the center speaker.

Delay Time Mode

Delay Time mode contains the following three settings.

DELAY-1:Select this setting if the rear speakers are further away from your listening position than the front speakers. (Delay time: 15 msec.)

DELAY-2:Select this setting if the rear speakers and front speakers are about the same distance way from your listening position. (Delay time: 20 msec.)

DELAY-3:Select this setting if the rear speakers are nearer to your listening position than the front speakers. (Delay time: 25 msec.)

Adjusting the level of the Center Speaker

Adjust the level of the center speaker between +10 and –10. Set the level so that it is about the same as the level from the front speakers.

Adjusting the level of the Rear Speakers

Adjust the level of the rear speakers between +10 and –10. Set the level so that it is about the same as the level from the front speakers.

You cannot adjust the levels of the left and right rear speakers independently.

English

Getting Ready to Use Dolby Pro Logic ——————————

Speaker arrangements for Dolby Pro Logic

Layout when using the center speaker

and rear speakers

Front	TV	Front
Speaker	Center Speaker	Speaker
	Center Speaker

Layout when using the rear speakers

Front	TV	Front
Speaker		Speaker

Rear	Rear
Speaker	Speaker

Rear	Rear
Speaker	Speaker

17

Image 21

Contents XT-TD77R RX-TD77RIf in Doubt Consult a Competent Electrician Vorsicht Ausreichende Belüftung Voorzichtig Goede ventilatie vereistPrecaucion ventilación correcta RX-TD77R XT-TD77RClass Laser Product Installation of the Unit FeaturesPower cord How This Manual Is OrganizedTable of Contents How To Put Batteries In the Remote Control AccessoriesUsing the Remote Control Getting StartedConnecting the External Wire Connecting the System Control CordExternal Wire White LineUsing the Supplied Wire Antenna Connecting the FM AntennaUsing the Coaxial Type Connector Not Supplied AM antenna wire Not suppliedFor Dolby Pro Logic Reproduction Connecting the SpeakersConnection Speakers aConnecting a TV Connecting a VCRConnecting the MD Player Audio OUTSetting the Clock To correct a mistake Adjusting the Brightness of the DisplayCommon Operations Turning the Power On and OffDisplay Turning the System OnBalance adjustment Adjusting the VolumeReinforcing the Bass Sound Fade Muting FunctionSelecting a S.E.A. Effect Mode A. ModeCustomizing a S.E.A. Effect Mode A. effect modesSelect the number for the Manual setting Using the UnitUsing the Remote Control On JVC’s 3D-PHONIC Mode Using the Surround Processor On DAP Mode On Dolby Pro Logic ModePlaying the Source Using the 3D-PHONIC Modes Playing the Source Using the DAP Modes To cancel the DAP mode, select OFF in step= Jazz Club = SYMPHONY= News = OFF = back to the beginning Playing the Source Using Dolby Pro Logic Mode Preparing the Dolby Pro Logic ReproductionGetting Ready to Use Dolby Pro Logic Select the Delay time Select the desired Center Speaker modeSet the volume to the level you normally use Adjust the level for the center speakerStart playback from the desired source Using the Dolby Pro LogicTuning In a Station Using the TunerSwitching between Frequency Bands One Touch RadioTo Change the FM Reception Mode Presetting StationsSelecting a radio station What Information RDS can Provide Receiving FM Stations with RDSChanging the Display Searching for Programmes by PTY codesPTY EON Function Setting EON Standby reception Press the EON ON/OFF buttonPress the 3 PTY Search button again Info =Blinking Alarm functionUsing the CD Player Disc button indicatorDisc display Power comes on, and operations are done automatically Basics of Using the CD Player Continuous PlayQuickest Way To Start a CD Is With the One Touch Operation To Insert DiscsPlace a CD onto the tray Press the same 0 button again Push the disc tray for Disc 3 to the backTo Play a Disc To Change Discs While PlayingTo Select a Track Programming the Playing Order of the Tracks Locating a Track With the Remote Control DirectlyTo Select a Passage Within a Track CD P.MODETrack Press the cursor key to the right Or left 4 or ¢ to selectPress the 3 or CD button Select a disc with the Disc 1-3 buttonsTo Check the Program Random PlayTo Modify the Program RandomRepeat Repeating a Track or the DiscsSEA Control ï + Press the up Á cursor key ALL ï 1 CD ï 1 ï OFF ïTray Lock Function Using the Remote Control Press the Repeat buttonLocking the Electronic Lock Unlocking the Electronic LockOne Touch Play Using the Cassette DeckRegular Play Tape Direction Indicator and the DisplayReverse Mode Other Useful Features of the Cassette DeckMusic Scan Fast Forward and RewindREC Pause REC START/STOP CD REC Start Things To Know Before You Start RecordingStandard Recording How to create a blank section on the tapeTo Record Any Sound Source To Tape Checking the Tape Counter While RecordingCD Direct Recording Auto Edit RecordingAuto Edit Press the cursor key up or down Á or 1 and select the disc + Press the down Cursor keyPress the up Á Cursor key = Using the Timer Setting the Daily TimerMenu Cancel Sleep Set the On Time Set the Off TimeSelect the source you want to listen to Turning the Daily Timer On and Off To Turn the Daily Timer On Again Press the Menu button Setting the Once REC Recording TimerPress the SET button Press the Enter button Set the On Time and Off TimeTurning the Once REC Timer On and Off Before the Timer StartsTo Record at the Same Time Again Press the Menu button Timer Priority Setting the Sleep TimerTo Change the Sleep Timer Setting To Cancel the Sleep Timer SettingRemote Control supplied with System can control JVC VCRs Using the VCROperating a JVC VCR or TV TV SOUND/VCROperating a VCR other than JVC’s VCR Compact Discs Cassette Tapes Care And MaintenanceMoisture Condensation Cassette DeckSymptom TroubleshootingPossible Cause ActionSpecifications EN, GE, FR, NL, SP, IT 0497TNYNATJEM