JVC XT-TD77R Select the number for the Manual setting, Using the Unit, Using the Remote Control

Page 17

SEA CONTROL

SET

ENTER

4.Adjust the level of the low (LOW), middle (MID), or high (HIGH) tones.

Using the Unit

1.Select the “LOW”, “MID”, or “HIGH” tone ranges by adjusting the cursor keys left and right (4 or ¢).

The display changes with each press of the cursor keys as shown below.

+Press the left (4) cursor key ïLOW ï MID ï HIGH ï Press the right ( ¢) cursor key =

2.Adjust the level of the selected tone range by adjusting the cursor keys up and down ( Á or 1 ).

Pressing the Á cursor key increases the level in 2dB units, and pressing the 1cursor key decreases it in 2dB units.

• You can adjust the level between –6 dB and +6 dB in seven steps.

Using the Remote Control

1.Press the SEA CONTROL button.

2.Select the “LOW”, “MID”, or “HIGH” tone ranges by pressing the 41 or Á ¢ button.

The display changes with each press of the buttons as shown below.

+Press the 41 button ïLOW ï MID ï HIGH ï Press the Á ¢ button=

3.Adjust the level of the selected tone range by pressing the 3 or 7 button.

You can adjust the level between –6 dB and +6 dB in seven steps.

5. Press the SET button.

“MANUAL 1” blinks on the display.

SEA	SEA
	CONTROL

6.Select the number for the MANUAL setting.

Using the Unit

Press the cursor key to the right or left ( 4 or ¢) and select the number.

Using the Remote Control

Select the number by pressing the 41or Á ¢ button.

The display changes with each press of the buttons or cursor keys as shown below.

On the unit:

+Press the left ( 4 ) button

ïMANUAL 1ï MANUAL 2 ïMANUAL 3 ï Press the right ( ¢ ) button=

On the Remote Control:

+Press the 41 button

ïMANUAL 1ï MANUAL 2 ïMANUAL 3 ï Press the Á ¢ button=

7. Press the ENTER button.

	“MEMORY” and the selected memory number are
	displayed on the screen, and the adjusted settings are
	stored in memory. After a few seconds, the display reverts		SEA
	to the item that was displayed before you pressed	SEA	SEA
		SEA	CONTROL

	the MENU button.

•The memory setting will appear in the S.E.A. effect mode using the manual number.

If you store new settings to a MANUAL number that has already been used, the new settings replace the existing setting.

English

13

Image 17

Contents XT-TD77R RX-TD77RIf in Doubt Consult a Competent Electrician Vorsicht Ausreichende Belüftung Voorzichtig Goede ventilatie vereistPrecaucion ventilación correcta RX-TD77R XT-TD77RClass Laser Product Installation of the Unit FeaturesPower cord How This Manual Is OrganizedTable of Contents How To Put Batteries In the Remote Control AccessoriesUsing the Remote Control Getting StartedConnecting the External Wire Connecting the System Control CordExternal Wire White LineUsing the Supplied Wire Antenna Connecting the FM AntennaUsing the Coaxial Type Connector Not Supplied AM antenna wire Not suppliedFor Dolby Pro Logic Reproduction Connecting the SpeakersConnection Speakers aConnecting a TV Connecting a VCRConnecting the MD Player Audio OUTSetting the Clock To correct a mistake Adjusting the Brightness of the Display Common Operations Turning the Power On and Off Display Turning the System OnBalance adjustment Adjusting the VolumeReinforcing the Bass Sound Fade Muting FunctionSelecting a S.E.A. Effect Mode A. ModeCustomizing a S.E.A. Effect Mode A. effect modesUsing the Remote Control Select the number for the Manual settingUsing the Unit On JVC’s 3D-PHONIC Mode Using the Surround ProcessorOn DAP Mode On Dolby Pro Logic ModePlaying the Source Using the 3D-PHONIC Modes = Jazz Club = SYMPHONY= News = OFF = back to the beginning Playing the Source Using the DAP ModesTo cancel the DAP mode, select OFF in step Getting Ready to Use Dolby Pro Logic Playing the Source Using Dolby Pro Logic ModePreparing the Dolby Pro Logic Reproduction Select the Delay time Select the desired Center Speaker modeSet the volume to the level you normally use Adjust the level for the center speakerStart playback from the desired source Using the Dolby Pro LogicTuning In a Station Using the TunerSwitching between Frequency Bands One Touch RadioSelecting a radio station To Change the FM Reception ModePresetting Stations What Information RDS can Provide Receiving FM Stations with RDSPTY Changing the DisplaySearching for Programmes by PTY codes EON Function Setting EON Standby reception Press the EON ON/OFF buttonPress the 3 PTY Search button again Info =Blinking Alarm functionDisc display Using the CD PlayerDisc button indicator Power comes on, and operations are done automatically Basics of Using the CD Player Continuous PlayQuickest Way To Start a CD Is With the One Touch Operation To Insert DiscsPlace a CD onto the tray Press the same 0 button again Push the disc tray for Disc 3 to the backTo Select a Track To Play a DiscTo Change Discs While Playing Programming the Playing Order of the Tracks Locating a Track With the Remote Control DirectlyTo Select a Passage Within a Track CD P.MODETrack Press the cursor key to the right Or left 4 or ¢ to selectPress the 3 or CD button Select a disc with the Disc 1-3 buttonsTo Check the Program Random PlayTo Modify the Program RandomRepeat Repeating a Track or the DiscsSEA Control ï + Press the up Á cursor key ALL ï 1 CD ï 1 ï OFF ïTray Lock Function Using the Remote Control Press the Repeat buttonLocking the Electronic Lock Unlocking the Electronic LockOne Touch Play Using the Cassette DeckRegular Play Tape Direction Indicator and the DisplayReverse Mode Other Useful Features of the Cassette DeckMusic Scan Fast Forward and RewindREC Pause REC START/STOP CD REC Start Things To Know Before You Start RecordingStandard Recording How to create a blank section on the tapeTo Record Any Sound Source To Tape Checking the Tape Counter While RecordingAuto Edit CD Direct RecordingAuto Edit Recording Press the up Á Cursor key = Press the cursor key up or down Á or 1 and select the disc+ Press the down Cursor key Menu Cancel Sleep Using the TimerSetting the Daily Timer Select the source you want to listen to Set the On TimeSet the Off Time Turning the Daily Timer On and Off To Turn the Daily Timer On Again Press the Menu button Setting the Once REC Recording TimerPress the SET button Press the Enter button Set the On Time and Off TimeTo Record at the Same Time Again Press the Menu button Turning the Once REC Timer On and OffBefore the Timer Starts Timer Priority Setting the Sleep TimerTo Change the Sleep Timer Setting To Cancel the Sleep Timer SettingRemote Control supplied with System can control JVC VCRs Using the VCROperating a JVC VCR or TV TV SOUND/VCROperating a VCR other than JVC’s VCR Compact Discs Cassette Tapes Care And MaintenanceMoisture Condensation Cassette DeckSymptom TroubleshootingPossible Cause ActionSpecifications EN, GE, FR, NL, SP, IT 0497TNYNATJEM