ProForm PFTL98908.1 user manual HOW to Fold and Move the Treadmill, HOW to Move the Treadmill

Page 20

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill, adjust the incline to the lowest position. If you do not do this, you may damage the treadmill when you fold it. Remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill.

1.Hold the metal frame firmly in the location shown by the arrow at the right. CAUTION: To decrease the pos- sibility of injury, do not lift the frame by the plastic foot rails. Make sure to bend your legs and keep your back straight as you raise the frame. Raise the frame about halfway to the vertical position.

2.Raise the frame until the latch knob locks into the storage position. Make sure that the latch knob is locked in the storage position.

To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of di- rect sunlight. Do not leave the treadmill in the storage position in temperatures above 85° F (30° C).

HOW TO MOVE THE TREADMILL

Before moving the treadmill, convert the treadmill to the stor- age position as described above. Make sure that the latch knob is locked in the storage position.

1.Hold a handrail and place one foot against one of the wheels.

2.Tip the treadmill back until it rolls freely on the wheelsNever. Carefully move the treadmill to the desired location. move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not attempt to move the treadmill over an uneven surface.

3.Place one foot against a wheel, and carefully lower the treadmill until it is resting in the storage position.

Frame

Latch Knob

Handrail

Wheel

20

Image 20
Contents QUESTIONS? Model No. PFTL98908.1 Serial NoMon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Pulse sensors are not medical devicesPage Before YOU Begin Assembly Overtighten the Nut the Wheels must turn Freely Make sure that the power cord is unpluggedDo not fully fold the Frame yet See the inset drawing. Tie the wire tie Pinch the Wire Harness 84. Partially tightenBolts touch the Base do not fully tighten Patch Bolts yet Not fully fold the Frame yetTouch the Base do not fully tighten the Patch Bolts yet Do not tighten the Bolts yetPage Be careful not to pinch the wires in the Right Handrail Be careful not to pinch the wires. Reattach PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consolePage HOW to USE a Preset Workout Select one of the preset workouts. To select oneHOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. PFTL98908.1 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL98908.1 R0809A Exploded Drawing B-Model No. PFTL98908.1 R0809A Exploded Drawing C-Model No. PFTL98908.1 R0809A Exploded Drawing D-Model No. PFTL98908.1 R0809A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty