ProForm PFTL98908.1 user manual Troubleshooting, Problem The power turns off during use

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 13). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 13. IMPORTANT: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has

Tripped

Reset

tripped. To reset the circuit breaker, wait for five

minutes and then press the switch back in.

 

 

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 19 to turn off the demo mode.

 

 

PROBLEM: The displays of the console do not function properly

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

 

 

THE POWER CORD. With the help of a second

 

 

person, carefully tip the Uprights (81, 83) down.

81

 

 

There may be three #8 x 2" Screws (21) in the bot-

 

 

tom of the Belly Pan (76). If there are, remove

 

 

 

them. Note: A Phillips screwdriver with a shaft at

83

 

 

least 5 in. (13 cm) long is required. Then, raise the

 

 

Uprights.

 

 

 

 

76

21

21

 

 

 

21

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL98908.1 Serial No On the WEBTable of Contents Important Precautions Pulse sensors are not medical devicesPage Before YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedOvertighten the Nut the Wheels must turn Freely Bolts touch the Base do not fully tighten Patch Bolts yet See the inset drawing. Tie the wire tiePinch the Wire Harness 84. Partially tighten Not fully fold the Frame yetTouch the Base do not fully tighten the Patch Bolts yet Do not tighten the Bolts yetPage Be careful not to pinch the wires in the Right Handrail Be careful not to pinch the wires. Reattach HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consolePage HOW to USE a Preset Workout Select one of the preset workouts. To select oneHOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. PFTL98908.1 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PFTL98908.1 R0809A Exploded Drawing B-Model No. PFTL98908.1 R0809A Exploded Drawing C-Model No. PFTL98908.1 R0809A Exploded Drawing D-Model No. PFTL98908.1 R0809A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents