ProForm PFTL99806.3 user manual Problem The walking belt slows when walked on

Page 23

Next, locate the Reed Switch (20) and the Magnet

(12)on the left side of the Pulley (11). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If neces- sary, loosen the indicated 3/4" Tek Screw (29), move the Reed Switch slightly, and then retighten the Screw. Then, reattach the Hood with the six 3/4" Screws (not shown), and run the treadmill for a few minutes to check for a correct speed reading.

Top

 

View

 

29

1/8 in.

20

11

12

 

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 3 to 4 in. (8 to 10 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few min- utes. Repeat until the walking belt is properly tight- ened.

b

3–4 in.

 

Rear Roller Bolts

c. If the walking belt still slows when walked on, please see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walk- ing belt has shifted to the right, turn the left rear roller bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b.If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 3 to 4 in. (8 to 10 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

a

b

23

Image 23
Contents On the WEB QUESTIONS?Please do not Contact Call TOLL-FREETable of Contents Important Precautions Page Power Lines Service Before YOU Begin Assembly Bolts yet Ful not to pinch the Upright Wire HarnessDo not tighten the Bolts yet Wires are pinched Page Page HOW to Connect AN External Source Using a Catv Cable HOW to Connect a 75 OHM Catv CablePRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeWhenkey. you are finished exercising, remove Turn on the fan if desiredMeasure your heart rate if desired HOW to USE a Preset ProgramSelect a preset program Press the Start button to start the programPress the Channel buttons to select Desired cable channel HOW to Operate the Personal TelevisionPress the Volume buttons to adjust the volume HOW to USE the Stereo Sound SystemPress the TV button again and select a cable Connection HOW to USE the Information ModeCable channels Optional Chest Pulse Sensor HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Problem Television reception is poor Problem The latch knob will not lock into placeExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description R0108AQty Exploded DRAWING-Model No. PFTL99806.3 122 120 110 104 116 97 102 111 87 114 90 82 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty