ProForm PFTL73105.2 user manual Troubleshooting, Problem The power turns off during use

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes, and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The display of the console does not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. With the help of a second person, carefully tip the Uprights (84) down as shown. Next, remove the three Screws (3) and the three Hood Screws (7). Note: A phillips screwdriver with a shaft at least 5” long is required.

a

3

7

 

 

3

 

 

84

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model No. PFTL73105.2 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Back Right SideAssembly Make sure that the power cord is unpluggedPage Page Wire HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeAvoid moving Measure your heart rate if desiredStand on Foot rails Turn on the fan if desiredSelect one of the personal trainer programs HOW to USE a Personal Trainer ProgramFollow your progress with the matrix Display HOW to Create a Custom Program Select one of the custom programsHOW to USE a Custom Program Select one of the pulse programs HOW to USE a Pulse ProgramIf pulse program 9 is selected, a pulse symbol If pulse programFollow your progress with the matrix Display Important If a Information MODE/DEMO ModeOptional Chest Pulse Sensor HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0406A Qty DescriptionDescription Exploded DRAWING-Model No. PFTL73105.2 67 82 105 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents