3.Attach the Weight Rack (90) to the Uprights (11) with the two Rack Washers (41) and Rack Bolts (89). Note: If nec- essary, spread the Uprights apart to align the holes in the Weight Rack with the holes in the Upright.
Insert the Left and Right Handrails (1, 88) into the upper end of the Uprights (11), with the lower end of each Handrail to the outside of the Extension Leg (34) as shown. Have a second person hold the Handrails until step 4 is completed.
4.With the help of a second person, lower the Uprights (11) until the Left and Right Handrails (1, 88) are resting on the floor. Attach the lower end of the Right Handrail (88) to the Extension Leg (34) with a Handrail Bolt (91), Handrail Washer (92), and Handrail Nut (93) as shown. Note: It may be necessary to push on the lower end of the Handrail to align the hole in the Handrail with the hole in the Extension Leg.
Attach the Left Handrail to the left Extension Leg (not shown) as described above.
Raise the Uprights (11) to the position shown in step 3.
5.Cut and remove the plastic tie holding the Wires (21).
Place the Console Base (46) on the right and left Uprights (11) (only the right Upright is shown). Connect the two indicated Wires (21) to the two connectors in the Console Base. Important: Make sure the Wires are fully inserted. WARNING: Do not disconnect or con- nect the Wires while the treadmill power cord is plugged in. Loosely thread four Screws (33) into the Uprights and the Console Base. After all four Screws have been started, tighten the Screws until they are snug; do not overtighten the Screws.
Thread the Cable Tie (16) through the Clamp (61), around the two Wires (21), and through the end on the Cable Tie. Pull the Cable Tie tight and cut off the end.
6.Attach the Storage Latch (14) to the left Upright (11) with two Small Screws (13). Be careful not to overtighten the Screws.
Place the Weights on the Weight Rack (90) with the
3 lbs. Weights (79) in the center of the Rack and 2 lbs. Weights next, followed by the 1 lbs. Weights.
3 |
|
|
|
|
| 41 | 89 | 90 |
|
|
|
| 41 | |
|
|
|
| |
| 1 |
|
| 89 |
| 11 |
|
| |
|
|
|
| 11 |
|
|
| 88 | |
|
|
|
| 34 |
4 |
|
|
|
|
|
|
|
| 34 |
| 11 |
|
| 93 |
|
|
|
| |
| 88 |
| 92 | |
|
|
| ||
|
|
|
| 91 |
5 | 11 |
|
|
|
|
|
|
| |
Cable |
|
|
|
|
Tie |
|
|
|
|
|
| 21 |
| |
Plastic Tie |
|
| Connectors | |
|
|
|
| 46 |
|
|
|
| 33 |
6 |
| 90 |
|
|
| 11 |
|
|
|
|
| 14 | 13 | 79 |
|
|
|
| |
7.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.
6