ProForm PFTL49100 user manual Calories/Fat

Page 9
Pulse Sensor
Pulse Indicator

1Insert the key fully into the power switch.

Note: Inserting the key will not turn on the dis- plays. The displays will

turn on when the ON/RESET button is pressed or when the walking belt is started. If

you just installed batter-

ies, the displays will already be on.

2Reset the console and start the walking belt.

Slide the speed control to the RESET position. Note: Each time the walking belt is stopped, the speed control must be moved to the RESET position before the walking belt can be restarted.

Next, slowly slide the speed control until the walking belt begins to move at slow speed. Carefully step onto the walking belt and begin exercising. Change the speed of the walk-

ing belt as desired by moving the speed control.

To stop the walking belt, step onto the foot rails and slide the speed control to the RESET position.

3Follow your progress with the four displays.

BURNING on page 14.) Every seven seconds, the display will change from one number to the other, as indicated by the mode arrows. This display also shows your pulse when the pulse sensor is used (see step 4).

The displays can be reset, if desired, by pressing the ON/RESET button.

4Measure your pulse, if desired.

To measure your pulse, stand on the foot rails and place your thumb on the pulse sensor as shown. The pulse sensor is pressure ac- tivatedÑfully press it

down. Do not press too hard, or the circu- lation in your thumb will be restricted, and your pulse will not be detected. Next, raise

your thumb slightly until the heart-shaped indicator in the pulse display flashes steadily. Hold your thumb at this level. After a few seconds, three dashes will appear in the display and your pulse will be shown. Hold your thumb on the sensor for another 15 seconds for the most accurate reading.

If the displayed pulse appears to be too high or too

TIME displayÑThis display shows the elapsed time.

DISTANCE displayÑ This display shows the distance that you have walked or run, in miles.

SPEED displayÑThis display shows the speed of the walking belt, in miles per hour.

CALORIES/FAT

CALORIES/PULSE displayÑThis display shows the approximate numbers of calories and fat calories you have burned. (See FAT

Mode Arrows

low, or if your pulse is not displayed, lift your thumb off the sensor and allow the display to reset. Press down again on the sensor as described above. Make sure that your thumb is positioned as shown, and that you are applying the proper amount of pressure to the pulse sensor. Try the sensor several times until you become familiar with it. Remember to stand still while measuring your pulse.

5Adjust the incline of the treadmill as desired.

To change the incline, press the top or bottom of the in- cline control until the desired incline level is reached.

6Turn off the power.

To turn off the power, simply wait for about four minutes. If the walking belt is stationary and the console buttons are not pressed for four minutes, the power will turn off automatically. Remove the key from the console.

9

Image 9
Contents QUESTIONS? Model No. PFTL49100 Serial NoCustomer HOT Line Important Precautions Table of ContentsPage Before YOU Begin Right SideBack Cutters A rubber mallet AssemblyPage Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Diagram of the Console Battery InstallationSTEP-BY-STEP Console Operation CALORIES/FAT HOW to Fold and Move the Treadmill HOW to USE the Hand WeightsHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE HOW to Move the TreadmillMaintenance and TROUBLE-SHOOTING Problem The power turns off during useTop View Symptom the Walking Belt is OFF-CENTER Symptom the Walking Belt Slows When Walked onConditioning Guidelines Exercise IntensityWorkout Guidelines Suggested Stretches Exercise FrequencyQty Description Part LISTÑModel No. PFTL49100Exploded DRAWINGÑModel No. PFTL49100 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT