ProForm PFTL49820 user manual Troubleshooting, Problem The power turns off during use, Top

Page 20

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.If the treadmill still will not run, please call our Customer Service Department toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the two 3/4” Screws (2) from the hood, and carefully pivot the Hood (1) off.

a

2

1

Locate the Reed Switch (10) and the Magnet (18) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (26) and move the Reed Switch slightly. Retighten the Screw. Re-attach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8”

17

10

 

26

18

Top

 

View

 

20

Image 20
Contents Customer HOT Line QUESTIONS?Model No. PFTL49820 Serial No Table of Contents Important PrecautionsPage Back Before YOU BeginRight Side Assembly Page Ties Opening Performant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DrawingHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key fully into the consoleWhenkey. you are finished exercising, remove Distance/LapsMeasure your heart rate, if desired HOW to USE a Workout Program When the program ends, remove the key from the consoleInsert the key into the console Select one of the workout programsHOW to Connect Your Portable Stereo HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Adapter Audio CableRCA Y-adapter PressVCR. the Play button on your CD player orMeasure your heart rate if desired Follow the on-line instructions to start the program HOW to USE Programs Directly from OUR WEB SiteWhen the program ends, remove the key HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Top TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Conditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty Part Identification Chart Part LIST-Model No. PFTL49820 Key Qty DescriptionPFTL49820