ProForm PFTL73105.1 user manual

Page 8

5.Place the treadmill in the storage position (see HOW TO FOLD AND MOVE THE TREADMILL on page 20).

Next, place the cylinder end of the Shock (92) near the bracket on the base of the Uprights (84).

See the two small inset drawings. Using your fingernail or the end of a screwdriver, press on the end of the Shock Pin (25) to loosen it from the Shock (92). Next, ro- tate the Shock Pin and pull it out of the Shock. Be care- ful to avoid losing the Shock Pin.

See drawing 5a. Press the cylinder end of the Shock (92) onto the ball on the bracket. Next, insert the end of the Shock Pin (25) through two of the small holes in the end of the Shock. Then, rotate the Shock Pin until it clips onto the Shock.

6.Raise the Shock (92) to a vertical position. Remove the Shock Pin (25) from the raised end of the Shock as de- scribed in step 5. If necessary, rotate the Shock to align the end of the Shock with the ball on the bracket on the Frame (58).

Plug in the power cord as described on page 10. Turn on the power as described on page 12. Next, press the Incline increase and decrease buttons until the ball on the bracket is aligned with end of the Shock (92). Then, press the end of the Shock onto the ball. Note: It may be necessary to press the end of the Shock onto the ball while the Frame is moving.

See drawing 6a. Insert the Shock Pin (25) into the two in- dicated small holes in the end of the Shock (92). Then, rotate the Shock Pin until it clips onto the Shock. Note: Extra Shock Pins are included.

Press the Incline decrease button until the treadmill is at the lowest incline level. Then, unplug the power cord.

5

 

 

 

25

 

 

 

 

 

 

84

 

 

 

 

25

 

 

 

92

Bracket

 

 

 

 

25

 

 

 

 

 

 

 

Cylinder

 

5a

 

 

 

 

 

 

25

 

 

 

92

 

Bracket

 

 

 

 

 

6

 

 

58

 

 

 

 

 

 

 

 

Bracket

 

 

 

 

25

 

 

 

 

92

 

6a

 

 

 

 

 

 

Holes

 

 

 

 

 

92

 

 

 

25

 

 

7.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included allen wrench in a secure place; the large allen wrench is used to adjust the walking belt (see page 23).

8

Image 8
Contents Call TOLL-FREE QUESTIONS?Model No. PFTL73105.1 Serial No Table of Contents Important Precautions Page Before YOU Begin Back Right SideAssembly Make sure that the power cord is unpluggedPage Page Wire PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Stand on Foot railsMoving your Turn on the fan if desiredFollow your progress with the matrix Display HOW to USE a Personal Trainer ProgramSelect one of the personal trainer programs HOW to Create a Custom Program Select one of the custom programsHOW to USE a Custom Program HOW to USE a Pulse Program If pulse program 9 is selected, a pulse symbolSelect one of the pulse programs If pulse programFollow your progress with the matrix Display Optional Chest Pulse Sensor Information MODE/DEMO ModeImportant If a HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top Conditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches R1105A Qty DescriptionDescription Exploded DRAWING-Model No. PFTL73105.1 67 82 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty