ProForm 831.24745.1 user manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

Make sure that the power cord is unplugged. Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal con- dition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key

and your own Phillips screwdriver

and

adjustable wrench

.

 

 

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST on page 23. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. Extra hardware may be included. If a part is missing, call toll-free1-888-533-1333. To avoid damaging plastic parts, do not use power tools for assembly.

3/4" Screw (10)–5

 

 

 

Base Pad Spacer

3/8" Star

5/16" Star

3/8" Nut (8)–2

Washer (9)–4

Washer (7)–4

 

(25)–2

 

 

 

1" Tek Screw (56)–4

 

3/8" x 2" Bolt (4)–2

 

 

5/16" x 1" Bolt (5)–4

3/8" x 4" Bolt (6)–4

 

1. Make sure that the power cord is unplugged.

1

B

 

With the help of a second person, carefully tip

 

 

A

the treadmill onto its left side. Partially fold the

 

 

Frame (53) so that the treadmill is more stable;

 

 

 

do not fully fold the Frame yet.

 

Hole

78

Remove and discard the two indicated bolts (A)

 

80

 

and the shipping bracket (B).

53

 

79

 

 

 

Cut the tie securing the Upright Wire (78) to the

4

 

56

Base (80). Locate the tie in the indicated hole in

 

 

 

 

 

 

the Base, and use the tie to pull the Upright Wire

 

 

Tie

out of the hole.

 

 

 

Attach a Base Pad (79) to the Base (80) in the lo-

25

 

 

cation shown with a Base Pad Spacer (25) and a

 

79

 

1" Tek Screw (56). Then, attach another Base

 

56

 

Pad (79) with only a 1" Tek Screw (56).

 

 

 

 

6

 

 

Image 6
Contents Model No Serial No Sears, Roebuck and Co., Hoffman Estates, ILTable of Contents Important Precautions Page Before YOU Begin Right SideBack Assembly Make sure that the power cord is unpluggedDo not fully fold the Frame yet Nut the Wheel must turn freely. Discard Not fully fold the Frame yetDo not fully tighten the Bolts yet Try again. if the Connectors are notBase 80. Be careful not to pinch the Upright Bolts and then tighten themScrews and then tighten them Raise the Frame 53 to the position shown Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeCalories/Pulse Time display-WhenDistance/Incline dis Measure your heart rate if desiredHOW to USE a Preset Workout Select a preset workoutCustomize your workout if desired Monitor your progress with the matrix and the displays Information Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyR1207A Qty DescriptionIf a part is missing, call toll-free Exploded Drawing A-Model No Exploded Drawing B-Model No Exploded Drawing C-Model No Exploded Drawing D-Model No ONE Year Full Warranty Get it fixed, at your home or ours