JVC RX-ES1SL manual Troubleshooting, General, Problem Possible Cause Solution

Page 40

Troubleshooting

Use this chart to help you solve daily operational problems. If there are any problems you cannot solve, contact your JVC’s service center.

General

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not come on.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if necessary.

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute.

 

 

 

 

An incorrect input mode (analog or digital)

Select the correct input mode (analog or digital).

 

is selected.

 

 

 

 

 

 

 

Connections are incorrect.

Check connections.

 

 

 

 

Sound from one speaker only.

The balance is set to one extreme.

Adjust the balance properly (see page 22).

 

 

 

 

The STANDBY lamp lights up after

Speakers are overloaded because of high

1. Press STANDBY/ON

on the front panel to turn

turning on the power, but soon the unit

volume.

off the unit.

 

turns off (into standby mode).

 

2. Stop the playback source.

 

 

3. Turn on the unit again, and adjust the volume.

 

 

 

 

 

Speakers are overloaded because of a

Check the speaker wiring.

 

 

short circuit at the speaker terminals.

If speaker wiring is not short-circuited, contact your

 

 

dealer.

 

 

 

 

 

The unit is overloaded because of a high

Consult your dealer after unplugging the power cord.

 

voltage.

 

 

 

 

 

Remote control does not operate as

The remote control is not ready for your

Press a source selecting button or TONE first, then

you intend.

intended operation.

press the buttons you want to use. (See pages 21

 

 

and 34 – 37.)

 

 

 

 

 

Remote control does not work.

There is an obstruction hiding the remote

Remove the obstruction.

 

 

sensor on the unit.

 

 

 

 

 

 

 

Batteries are weak.

Replace batteries.

 

 

 

 

 

The mode selector is set to the incorrect

Set the mode selector to the proper position.

 

position.

 

 

 

 

 

Bass sound is reinforced too much

Appropriate bass level is not selected.

Adjust audio position level (see page 22).

when listening in stereo.

 

 

 

38

Page 39 Page 41
Image 40
Page 39 Page 41
Contents RX-ES1SL Mises en garde, précautions et indications diverses For Canada/pour Le CanadaTable of Contents Remote control Parts identificationParts identification Front panelBefore installation Checking the supplied accessoriesPutting batteries in the remote control Getting startedAM antenna connection Connecting the FM and AM antennasFM antenna connection Connecting the speakers Speaker Layout DiagramConnecting the subwoofer Connecting the front, center, and surround speakersConnecting video components When connecting a DVD player with stereo output jacksDVD player connection Turn off all components before making connectionsVCR connection TV connection DBS tuner connectionConnecting the power cord Plug the power cord into an AC outletDigital connection Digital coaxial cordTurn on the power To turn off the power into standbySelecting the analog or digital input mode Basic operationsAdjust the volume Selecting the digital decode modeListening with headphones Always set the mode selectorTimer From the remote control onlyTurning off the sounds temporarily- Muting Press Sleep repeatedlyBasic adjustment of auto memory Signal and speaker indicators on the displaySpeaker indicators light up as follows Changing the display brightnessSpeaker settings TV/VCR/DBSPress Setting Turn Multi JOG until Quick Setup appears on the displayPress SET to finish the setting Press SETWhen selecting Medium Room When selecting Large RoomLeft Basic settings Operating procedureSetting Auto Surround-AUTO SR Setting the video component input mode-DVD VIDEO/DBS VideoSound adjustments Adjusting the tone-BASS, TrebleAdjusting the subwoofer output level Press AdjustAdjusting the front speakers output balance-BAL Attenuating the input signal-ATTWhen using the remote control Press Bass Boost Reinforcing the bass-B.BOOSTTuning in to stations manually Using preset tuningFrom the remote control only Press FM/AM to select the band Tuner operationsSelecting the FM reception mode To tune in a preset stationFrom the remote control Press FM/AM to select the band Press Tuner PresetCreating realistic sound fields Reproducing theater ambienceIntroducing the Surround/DSP modes Surround modesDAP Digital Acoustic Processor modes DSP Digital Signal Processor modesAll Channel Stereo Using Surround modes From the remote controlPress Surround to select an appropriate Surround mode Select and play software you likeTurn Multi JOG to select an appropriate surround mode Press Test to check the speakers output balancePress Test again to stop the test tone Press SurroundUsing DSP modes Repeat steps 5 and 6 to adjust the other settingsAlways set the mode selector to AUDIO/TV/VCR/DBS To cancel Surround modeTo cancel DSP Modes Effect available only for DAP modes *2Using the DVD Multi playback mode Adjusting the speaker output levelFrom the remote control Press DVD Multi Turn Source Selector until DVD Multi appears on the displayAV Compu Link remote control system TV’s Video Input 1 terminal using S-video cordsVideo input using composite video cords Connections 2 Video Cable ConnectionAutomatic selection of TV’s input mode Automatic power On/OffOne-touch video play One-touch DVD playOperating other JVC products DVD playerOperating other manufacturers’ equipment DBSManufacturers’ codes for Catv converter Manufacturers’ codes for DBS tunerChanging the transmittable signals for operating a Manufacturers’ codes for VCRChanging the transmittable signals for operating a TV VOL + Adjust the volumeIf more than one codes are listed for your brand of TV, try Manufacturers’ codes for TVProblem Possible Cause Solution TroubleshootingGeneral Surround/DSP FM/AMSpecifications RX-ES1SLLimited Warranty Authorized Service Centers  2003 Victor Company of JAPAN, Limited 0403NHMMDWJEIN AMPLI-TUNER Cinema Maison Mises en garde, précautions et indications diverses English English Parts identification Putting batteries in the remote control Connecting the FM and AM antennas Connecting the speakers Connecting video components English Connect using one Connecting the power cord English Adjust the volume Turning off the power with the Sleep When digital input is selected Lights up when the left Following signal indicators light upWhen digital input is selected Lights up when the right Speaker settings Initial setting USEFeet M 8 feet Feet M 8 feet Basic settings Comp Mode-DVD VIDEO/DBS VideoOFF Sound adjustments Reinforcing the bass-B.BOOST Tuner operations Selecting the FM reception mode Introducing the Surround/DSP modes Creating realistic sound fields Surround/DSP modes About relations between speaker layout Using Surround modesSee pages 15 to Lpcm Subwfr VOL Surr L*1 CENTER*1Surr R*1 Effect 3 Effect 4 Effect Effect 2 Effect Using the DVD Multi playback mode AV Compu Link remote control system cannot control the DBS AV Compu Link remote control system Operating other JVC products Operating other manufacturers’ equipment Operating other manufacturers’ equipment Try to operate your TV by pressing TV General Troubleshooting Specifications EN, FR
Related manuals
Manual 76 pages 34.39 Kb

RX-ES1SL specifications

The JVC RX-ES1SL is a compact and versatile stereo receiver designed to cater to the audio needs of home entertainment enthusiasts. Known for its excellent sound quality and user-friendly features, it presents an ideal solution for those who seek an integration of traditional and modern audio technologies.

One of the standout features of the RX-ES1SL is its power output, which delivers a robust 100 Watts per channel. This ensures that listeners can enjoy rich, clear audio across a variety of listening environments, whether in a small room or a larger space. The receiver is designed to drive both high-efficiency bookshelf speakers as well as larger floor-standing models, making it adaptable to various setups.

Incorporating advanced audio technologies, the RX-ES1SL features a built-in Digital Signal Processor (DSP), which enhances audio performance through various sound modes and effects. This allows users to customize their listening experience, whether they're watching movies, playing video games, or enjoying music. The receiver also supports several audio formats, ensuring compatibility with different devices and media types.

Connectivity is another strong point of the JVC RX-ES1SL. It includes multiple inputs, such as RCA for analog sources, and an optical input for digital audio connections. Additionally, it has AM/FM radio capabilities, allowing users to tune into their favorite stations easily. The USB port offers convenience for connecting external storage devices, providing direct playback of digital files without needing an additional player.

Aesthetically, the RX-ES1SL features a sleek design that fits into various decors. Its compact footprint makes it suitable for smaller spaces or as part of a larger home theater system. The user-friendly interface, complete with a remote control, simplifies operation and enhances the overall user experience.

For music lovers, the JVC RX-ES1SL is equipped with a high-performance tuner, ensuring clear reception of AM and FM signals. It also features a highly accurate frequency response that enables a wide dynamic range, delivering nuanced audio that can bring both music and soundtracks to life.

In summary, the JVC RX-ES1SL is a well-rounded stereo receiver that combines robust audio performance with modern connectivity options. Its ability to adapt to various audio sources, coupled with a compact design and user-friendly interface, makes it an excellent choice for anyone looking to enhance their home audio experience. Whether you are a casual listener or a dedicated audiophile, the RX-ES1SL is equipped to satisfy your audio cravings.
Top Page Image Contents