JVC RX-ES1SL manual Effect 3 Effect 4 Effect Effect 2 Effect

Page 77

Creating realistic sound fields

English

4Adjust the surround speaker output levels (from –10 dB to +10 dB).

•Make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers.

To adjust the left surround speaker level,

press SURR L +/–.

To adjust the right surround speaker level,

press SURR R +/–.

L R

LPCM SUBWFR DSP

VOL

5Turn MULTI JOG until the setting item you want to set appears on the display, then press SET.

•As you turn MULTI JOG, the indication changes as follow:

L R

LPCM SUBWFR DSP

VOL

BASS

 

 

TREBLE

 

 

 

SUBWFR

 

 

 

 

 

 

 

 

CENTER

 

 

SURR L

 

 

 

SURR R

 

 

 

 

 

 

 

 

 

EFFECT*

 

 

 

PANORAMA

 

 

 

BAL

 

 

 

 

 

 

 

B.BOOST

 

 

ATT

 

 

(Back to the beginning)

 

 

 

Ex.: When selecting “–8 (dB)” for “SURR R.”

5Press TEST again to stop the test tone.

6Only for DAP modes:

Press EFFECT to select the DAP effect level (1 to 5) you want.

•As the number increases, the DAP effect becomes stronger (normally set it to “EFFECT 3”).

L R

LPCM SUBWFR DSP

VOL

* Available only for DAP modes.

SURR L*1: To adjust the left surround speaker output level (from –10 dB to +10 dB).

SURR R*1: To adjust the right surround speaker output level (from –10 dB to +10 dB).

EFFECT (available only for DAP modes) *2:

To adjust the DAP effect level.

As the number increases, the effect becomes stronger (normally set it to “EFFECT 3”).

*1 “0 (dB)” is the initial setting for each speaker setting. *2 “3” is the initial setting.

EFFECT 3 EFFECT 4 EFFECT 5

EFFECT 2 EFFECT 1

On the front panel:

•No test tone is available when using the buttons on the front panel.

 

 

 

 

 

 

 

 

 

 

 

SOURCE SELECTOR

MASTER VOLUME

 

DIMMER

SETTING

ADJUST

SURROUND

 

 

 

 

 

SET / TUNER PRESET

/ MULTI JOG

 

 

 

 

 

 

 

 

 

 

 

 

 

PHONES

STANDBY / ON

STANDBY

 

 

 

DVD MULTI

DVD

DBS

VCR

TV

FM / AM

 

 

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

6Turn MULTI JOG to adjust the item selected in step 5, then press SET.

Your setting is stored.

•When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers.

L R

LPCM SUBWFR DSP

VOL

Ex.: When selecting “–8 (dB)” for “SURR R.”

7Repeat steps 5 and 6 to adjust the other settings.

1Start playing 2 channel software—either Linear PCM or analog signal—and select the source.

2Press SURROUND.

MULTI JOG now works for the Surround/DSP mode selection.

3Turn MULTI JOG until one of the DSP modes you want to apply appears on the display.

The DSP indicator lights up on the display.

•As you turn MULTI JOG, the indication changes as follow:

L R

LPCM SUBWFR DSP

VOL

PLII MOVIE

 

 

 

 

 

 

PLII MUSIC

 

 

 

 

 

 

 

 

LIVE CLUB

 

 

 

DANCE CLUB

 

 

 

 

 

 

HALL

 

 

 

 

 

PAVILION

 

 

 

 

 

 

 

ALL CH ST.

 

 

STEREO (Surround/DSP off)

 

(Back to the beginning)

 

 

 

 

 

4Press ADJUST.

MULTI JOG now works for the sound adjustment.

To cancel DSP Modes

Press SURROUND repeatedly on the remote control or press SURROUND then turn MULTI JOG on the front panel so that “STEREO” appears on the display. The DSP indicator goes off from the display.

NOTES

•You can adjust the speaker output levels using the remote control without outputting the test tone.

•You cannot adjust the center speaker output level and no test tone comes out of the center speaker when “CNTR SP” is set to “NO.”

•You cannot adjust the surround speaker output levels and no test tone comes out of the surround speakers when “SURR SP” is set to “NO.”

30

Page 76 Page 78
Image 77
Page 76 Page 78
Contents RX-ES1SL For Canada/pour Le Canada Mises en garde, précautions et indications diversesTable of Contents Parts identification Remote controlFront panel Parts identificationChecking the supplied accessories Before installationPutting batteries in the remote control Getting startedFM antenna connection Connecting the FM and AM antennasAM antenna connection Speaker Layout Diagram Connecting the speakersConnecting the subwoofer Connecting the front, center, and surround speakersWhen connecting a DVD player with stereo output jacks Connecting video componentsDVD player connection Turn off all components before making connectionsVCR connection DBS tuner connection TV connectionPlug the power cord into an AC outlet Connecting the power cordDigital connection Digital coaxial cordTo turn off the power into standby Turn on the powerSelecting the analog or digital input mode Basic operationsSelecting the digital decode mode Adjust the volumeListening with headphones Always set the mode selectorFrom the remote control only TimerTurning off the sounds temporarily- Muting Press Sleep repeatedlySignal and speaker indicators on the display Basic adjustment of auto memorySpeaker indicators light up as follows Changing the display brightnessTV/VCR/DBS Speaker settingsTurn Multi JOG until Quick Setup appears on the display Press SettingPress SET to finish the setting Press SETWhen selecting Large Room When selecting Medium RoomLeft Operating procedure Basic settingsSetting the video component input mode-DVD VIDEO/DBS Video Setting Auto Surround-AUTO SRAdjusting the tone-BASS, Treble Sound adjustmentsAdjusting the subwoofer output level Press AdjustAttenuating the input signal-ATT Adjusting the front speakers output balance-BALWhen using the remote control Press Bass Boost Reinforcing the bass-B.BOOSTUsing preset tuning Tuning in to stations manuallyFrom the remote control only Press FM/AM to select the band Tuner operationsTo tune in a preset station Selecting the FM reception modeFrom the remote control Press FM/AM to select the band Press Tuner PresetReproducing theater ambience Creating realistic sound fieldsIntroducing the Surround/DSP modes Surround modesAll Channel Stereo DSP Digital Signal Processor modesDAP Digital Acoustic Processor modes From the remote control Using Surround modesPress Surround to select an appropriate Surround mode Select and play software you likePress Test to check the speakers output balance Turn Multi JOG to select an appropriate surround modePress Test again to stop the test tone Press SurroundRepeat steps 5 and 6 to adjust the other settings Using DSP modesAlways set the mode selector to AUDIO/TV/VCR/DBS To cancel Surround modeEffect available only for DAP modes *2 To cancel DSP ModesAdjusting the speaker output level Using the DVD Multi playback modeFrom the remote control Press DVD Multi Turn Source Selector until DVD Multi appears on the displayTV’s Video Input 1 terminal using S-video cords AV Compu Link remote control systemVideo input using composite video cords Connections 2 Video Cable ConnectionAutomatic power On/Off Automatic selection of TV’s input modeOne-touch video play One-touch DVD playDVD player Operating other JVC productsDBS Operating other manufacturers’ equipmentManufacturers’ codes for Catv converter Manufacturers’ codes for DBS tunerManufacturers’ codes for VCR Changing the transmittable signals for operating aTV VOL + Adjust the volume Changing the transmittable signals for operating aIf more than one codes are listed for your brand of TV, try Manufacturers’ codes for TVGeneral TroubleshootingProblem Possible Cause Solution FM/AM Surround/DSPRX-ES1SL SpecificationsLimited Warranty Authorized Service Centers  2003 Victor Company of JAPAN, Limited 0403NHMMDWJEIN AMPLI-TUNER Cinema Maison Mises en garde, précautions et indications diverses English English Parts identification Putting batteries in the remote control Connecting the FM and AM antennas Connecting the speakers Connecting video components English Connect using one Connecting the power cord English Adjust the volume Turning off the power with the Sleep When digital input is selected Lights up when the right Following signal indicators light upWhen digital input is selected Lights up when the left Speaker settings USE Initial settingFeet M 8 feet Feet M 8 feet Basic settings OFF Mode-DVD VIDEO/DBS VideoComp Sound adjustments Reinforcing the bass-B.BOOST Tuner operations Selecting the FM reception mode Introducing the Surround/DSP modes Creating realistic sound fields See pages 15 to About relations between speaker layout Using Surround modesSurround/DSP modes Lpcm Subwfr VOL Surr R*1 CENTER*1Surr L*1 Effect 3 Effect 4 Effect Effect 2 Effect Using the DVD Multi playback mode AV Compu Link remote control system cannot control the DBS AV Compu Link remote control system Operating other JVC products Operating other manufacturers’ equipment Operating other manufacturers’ equipment Try to operate your TV by pressing TV General Troubleshooting Specifications EN, FR
Related manuals
Manual 76 pages 34.39 Kb

RX-ES1SL specifications

The JVC RX-ES1SL is a compact and versatile stereo receiver designed to cater to the audio needs of home entertainment enthusiasts. Known for its excellent sound quality and user-friendly features, it presents an ideal solution for those who seek an integration of traditional and modern audio technologies.

One of the standout features of the RX-ES1SL is its power output, which delivers a robust 100 Watts per channel. This ensures that listeners can enjoy rich, clear audio across a variety of listening environments, whether in a small room or a larger space. The receiver is designed to drive both high-efficiency bookshelf speakers as well as larger floor-standing models, making it adaptable to various setups.

Incorporating advanced audio technologies, the RX-ES1SL features a built-in Digital Signal Processor (DSP), which enhances audio performance through various sound modes and effects. This allows users to customize their listening experience, whether they're watching movies, playing video games, or enjoying music. The receiver also supports several audio formats, ensuring compatibility with different devices and media types.

Connectivity is another strong point of the JVC RX-ES1SL. It includes multiple inputs, such as RCA for analog sources, and an optical input for digital audio connections. Additionally, it has AM/FM radio capabilities, allowing users to tune into their favorite stations easily. The USB port offers convenience for connecting external storage devices, providing direct playback of digital files without needing an additional player.

Aesthetically, the RX-ES1SL features a sleek design that fits into various decors. Its compact footprint makes it suitable for smaller spaces or as part of a larger home theater system. The user-friendly interface, complete with a remote control, simplifies operation and enhances the overall user experience.

For music lovers, the JVC RX-ES1SL is equipped with a high-performance tuner, ensuring clear reception of AM and FM signals. It also features a highly accurate frequency response that enables a wide dynamic range, delivering nuanced audio that can bring both music and soundtracks to life.

In summary, the JVC RX-ES1SL is a well-rounded stereo receiver that combines robust audio performance with modern connectivity options. Its ability to adapt to various audio sources, coupled with a compact design and user-friendly interface, makes it an excellent choice for anyone looking to enhance their home audio experience. Whether you are a casual listener or a dedicated audiophile, the RX-ES1SL is equipped to satisfy your audio cravings.
Top Page Image Contents