TROUBLE-SHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.
d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on posi- tion.
PROBLEM: The power turns off during use
c | |
Tripped | Reset |
d | |
On | |
Position | |
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, please call our toll-free HELPLINE.
PROBLEM: The speed display on the console does not function properly
SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the screws from the hood and carefully remove the hood. Locate the Reed Switch
(21)and the Magnet (43) on the left side of the Pulley
(42).Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8Ó. If necessary, loosen the Reed Switch Screw (30) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.
Model No Serial No
SEARS, Roebuck and CO. Hoffman ESTATES, IL
Table of Contents
Important Precautions
Page
Left Side
Before YOU Begin
Right Side
Assembly
Driver , wire cutters , and rubber mallet
There may be extra screws after assembly is com- pleted
Pulse
HOW to Plug in the Power Cord
Operation and Adjustment
Performant Lubetm Walking Belt
Console Diagram
Features of the Console
HOW to Turn on the Power
HOW to USE the Manual Mode
CALS/FAT Cals
SPEED/MIN-MILE
Select one of the personal trainer programs
HOW to USE Personal Trainer Programs
Insert the key into the console
Measure your heart rate, if desired
HOW to Connect Your Portable Stereo
HOW to Connect Your Home Stereo
HOW to Connect Your Computer
HOW to Connect Your VCR
Audio Adapter Cable
Finished, remove the key
Program
HOW to USE Programs Directly from OUR Internet Site
Whenkey. the program is finished, remove
Optional Hand Weights
Information MODE/DEMO Mode
Optional Chest Pulse Sensor
HOW to Fold the Treadmill for Storage
HOW to Fold and Move the Treadmill
HOW to Move the Treadmill
HOW to Lower the Treadmill for USE
Problem The power turns off during use
TROUBLE-SHOOTING
Top
Problem The walking belt slows when walked on
3ÓÐ4Ó
Workout Guidelines
Conditioning Guidelines
Exercise Intensity
Exercise Frequency
Suggested Stretches
Page
Part LISTÑModel No
Key Qty Description
Exploded DRAWINGÑModel No
117 116 107 108 118 109 110 119 121 104 102
Model No
Full 90 DAY Warranty
SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL