ProForm PFTL14511.0 warranty Make sure that the power cord is unplugged

Page 7

1.

Make sure that the power cord is unplugged.

1

 

 

 

 

 

 

Place a piece of cardboard below the rear of the

 

 

 

 

 

 

Frame (56) to protect the floor or carpet.

 

 

 

 

 

 

 

Attach the Left Wheel Cap (96) to the Base (94)

 

 

 

 

56

 

 

with two #8 x 3/4" Screws (2).

 

 

 

 

 

 

Attach the Right Wheel Cap (not shown) to

 

 

 

 

 

 

 

the right side of the Base (94) in the same

 

 

 

 

 

 

 

way.

 

94

2

 

 

 

 

 

 

 

 

 

 

 

 

 

96 Cardboard

 

 

 

 

 

 

 

2. Pull the Upright Wire (81) and the Base Ground

2

 

 

 

 

 

 

Wire (110) through the indicated hole in the

 

 

 

 

 

 

Base (94).

 

 

 

 

 

 

 

Attach the Base Ground Wire (110) to the Base

 

 

Hole

 

 

 

 

(94) with a #8 x 1/2" Ground Screw (10).

 

 

 

 

 

 

 

 

 

81

 

 

 

 

 

 

 

10

110

94

 

 

 

 

 

 

 

3. Identify the Left Upright (89), which is marked

3

 

 

 

 

 

 

with a “Left” sticker or an “L” sticker. Have a sec-

 

81

 

 

 

 

ond person hold the Left Upright near the Base

 

 

 

 

 

 

(94).

 

 

 

 

89

 

 

See the inset drawing. Tie the wire tie in the

 

 

 

 

 

 

 

 

 

 

Wire

 

 

Left Upright (89) securely around the end of the

 

 

 

 

81

 

Upright Wire (81). Then, pull the other end of the

 

 

 

 

Tie

 

wire tie until the Upright Wire is routed com-

 

 

Wire

 

 

 

pletely through the Left Upright.

 

 

 

 

 

 

 

89

Tie

 

 

 

 

 

 

 

 

 

 

 

 

 

81

94

 

 

 

 

7

 

 

 

 

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents On the WEB QUESTIONS?Model No. PFTL14511.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Instructions Save TheseBefore YOU Begin Wrench Scissors AssemblySee the inset drawing. Tie the wire tie Make sure that the power cord is unpluggedBase Covers into place yet Be careful not to pinch the UprightTighten the Bolts yet. Note It may be helpful Attach the Right Upright not shownAttach the Right Handrail 87 in the same way Shown. Start all four Screws, and then tighten Each of them Important To avoid damagingAgain. if YOU do not Connect the CON Them All four Bolts, and then tighten eachConsole Make sure the caps remain in the ends Storage Latch Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console DiagramConsole HOW to SET UP the Console HOW to Turn on the PowerBegin working out HOW to USE the Manual ModeInsert the key into the console Page Turn on the fan if desired Measure your heart rate if desired. Before usingStart the workout HOW to USE AN Onboard WorkoutHOW to USE AN Ifit Live Workout Ifit Live FCC Information HOW to USE the Internet Browser Select the wireless network mode HOW to USE the Settings ModeSelect the unit of measurement Exit the settings modeLog in to your iFit Live account Select a languageSelect the settings mode. See on Select the maintenance mode HOW to USE the Maintenance ModeView technical information HOW to USE the Stereo Sound SystemHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillProblem The power turns off during use TroubleshootingOutlets Top Problem The walking belt slows when walked onTurn if the walking belt has shifted to the right Problem The buttons on the screen do not work correctly Problem The iFit Live mode does not function correctlyExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part ListQty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Related manuals
Manual 40 pages 31.48 Kb
Top Page Image Contents