ProForm PFEL05807 user manual Maintenance and Troubleshooting, Battery Replacement

Page 20

MAINTENANCE AND TROUBLESHOOTING

Inspect and tighten all parts of the elliptical exerciser regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.

BATTERY REPLACEMENT

If the console display becomes dim, the batteries should be replaced; most console problems are the result of low batteries. See assembly step 13 on page 11 for replacement instructions.

HOW TO LEVEL THE ELLIPTICAL EXERCISER

If the elliptical exerciser rocks slightly on your floor during use, see HOW TO LEVEL THE ELLIPTICAL EXERCISER on page 14.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the reed switch should be adjusted. To adjust the reed switch, first remove the screws from the left and right side shields; there are two sizes of screws in the side shields—note which size of screw you remove from each hole. Gently pull the side shields apart and remove the convenience tray.

Next, see the drawing below and locate the Reed Switch (50). Loosen, but do not remove, the indicated M4 x 16mm Self-tapping Screw (79). Slide the Reed Switch slightly toward or away from a Magnet (55) on the flywheel.

36

79

50

55

Then, retighten the Screw. Turn one of the Crank Arms

(36)for a moment. Repeat until the console displays correct feedback. When the Reed Switch is correctly adjusted, replace the convenience tray and reattach the left and right side shields.

HOW TO ADJUST THE DRIVE BELT

If the pedals slip while you are pedaling, even while the resistance is adjusted to the highest setting, the drive belt may need to be adjusted. To adjust the drive belt, first remove the screws from the left and right side shields; there are two sizes of screws in the side shields—note which size of screw you remove from each hole. Gently pull the side shields apart and remove the convenience tray.

Next, locate the Idler Screw (68) and loosen it one half turn. Step onto the elliptical exerciser and move the pedals. If the pedals continue to slip, turn the Idler Screw another half turn and test the pedals again. Continue in this way until the pedals no longer slip. Then, replace the convenience tray and reattach the side shields.

68

20

Image 20
Contents Call TOLL-FREE QUESTIONS?Model No. PFEL05807.1 Serial No Table of Contents Important Precautions Before YOU Begin Assembly Page Grease Repeat this step for the other side Elliptical exerciserWire Harness 48 between the Upright Wire HarnessScrews 95. Tip Start all screws before Tightening any of them. Avoid pinchingRepeat this step for the Left Handlebar not shown May become damaged. Remove the two bat Manufacturer-supplied power supply. PlugAre recommended. Important If the ellipti Avoid pinching the Wire Harness 48 during this step HOW to Exercise on the Elliptical Exerciser HOW to USE the Elliptical ExerciserHOW to Move the Elliptical Exerciser Page Console Diagram Features of the ConsoleBegin pedaling to turn on the console HOW to USE the Manual ModeSelect the manual mode Will turn off automatically When you are finished exercising, the consoleMeasure your heart rate if desired HOW to USE a Weight Loss Workout Press Start or begin pedaling to start the workoutHOW to USE a Preset Workout HOW to View the Fitness JournalMaintenance and Troubleshooting Battery ReplacementHOW to Adjust the Reed Switch HOW to Adjust the Drive BeltExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Exploded Drawing A-Model No. PFEL05807.1 R0108A R0108A Qty DescriptionQty Description PFEL05807.1 Exploded Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty